KERC600EAL5 KitchenAid Range - Instructions

removed the screws that secured the lower element. Disconnected the old element from wire contacts. Inserted the new element into the wire contacts.

I very simply replaced the gasket where it belonged and I was good to go!

Turned breaker off. Removed oven door for access, two screws loosened element, unplugged wires from element & removed element. Reverse order to install. Perfect fit. Thanks.

slide the glass in. Thank you for having such a wounderful place to get what others said we can not get this glass. Thank you again

Removed back panel on stove and found no continuity in bake element indicating a break in the element circuit. Also tested electrical supply up to the element and found that we had electricity up to the element when the oven was turned on. Went on line and ordered the bake element and it was on my doorstep in 48 hours. Remove 2 screws inside oven and disconnect wires from the rear and install new element and plug the 2 wires into it, replace rear panel ( 3screws) and turn electricity back on to the stove and you are back in business.

Remove two screws. Plug n play.

TURNED OFF THE POWER TO THE RANGE, DISCONNECTED THE ELECTRIC PLUG. I unscrewed the element attached to the oven, disconnected the connectors. Reconnected the element and screwed the part back to the oven. EASIER THEN I THROUGHT.

The part came in 2 days even though I chose the least expensive shipping method. The hardest part was unscrewing the old screws that held the old bake element in place. We soaked them in WD40, and after a while were able to unscrew them. The new element slid in place and works just fine.

Removed rear panel (6 screws) and disconnected the four connectors on the Broil element. Then removed the 4 screws holding the the element to the top of the oven cavity. Inserted new element and connected the 4 screws to secure it. Connected the four connectors and re-installed the rear panel.

Unscrew 3 screws across the front inside the oven door and the 2 screws on each side of the control panel. That allows for lifting the entire control panel from the front to access the switches from underneath. The old switch is held in place by the lug nut under the knob. Once removed, the 5 wires can be disconnected (carefully noting which wire connects to which terminal). The new switch is then connected, and then fastened back into place with the lug nut. The control panel is then re-secured by the five screws

I watched some videos on YouTube first that said you could flip a latch on the door hinges and remove the door entirely. On this older oven there was no latch, you just open the door to its first position and lift up and out to remove the door. Unlike newer doors leave this one face up on a table to work on it. Remove all (10?) of the screws along the bottom edge, pull away the side door trim pieces, then remove the outside panel of the door by lifting slightly then pulling downwards. Mine was actually a glass panel, so be careful. Remove the two screws holding the upper door trim down onto the hinge mechanisms and rotate the trim out of the way. Lift off the large metal cover to expose the first, outer glass, then remove the insulation, then remove the screws and clips holding down the metal frame around the inner glass. Clean everything well (I used a baking soda paste), then replace in the reverse order.

This is a built-in oven, so the biggest problem was figuring out how to remove it from the cabinet. The solution turned out to be removing the cooktop above it and unscrewing two screws that connected the oven to the inside of the cabinet. The other problem was removing BOTH metal backs from the oven. The first one was easy. The second one wasn't. The old socket was recessed behind the second back, making it virtually impossible to access the metal "wings" that hold it in place, so I ended up pulling out the socket assembly from inside the oven with pliers.

Remove three Phillips screws underneath front edge, raise front edge and lay it back on stovetop. Pull knob straight off, use pliers to loosen nut holding switch in place, remove nut. I took photos of the old switch with wires attached that also showed the numbers on the terminals in case I pulled off too many at once. The new switch isn't arranged the same as the old one, but follow the conversion table, and it will work fine. Remove and replace one wire at a time. When replacing the control panel don't try to just lay it flat and slide it back on -- it won't work. Easier if you hold it at about 90 degrees and pivot it back onto the rubber seal at the edge of the stovetop. Re-install the three screws, and you're done. The new switch fixed the problem perfectly. I took apart the old switch and found a broken metal piece inside, so I was confident this was the problem, and not some other component.

Had to screw off old terminal block & screw on new one

I received the replacement broil element for my Kitchenaid model KESH307 range 34 hours after placing the order online with PartSelect.com! I had previously removed the old element and verified that the outer circuit was open. I did this without removing the oven door. I realized that to install the new element with the door on would require me to have 5 foot long arms and a very flexible 2 foot long neck.

Turns out there are at least 3 different styles of door mounting in the Kitchenaid line. I found the correct one for my range, and when the new element arrived, I had the door off in a jiffy. Enlisting my spouse to hold the oven door switch so as to keep the light off (It shown in my eyes.), I installed the new element with minimal difficulty. It took me about 20 minutes.

Thank you PartSelect for being there and for the really quick delivery.