62946975 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Barbara from Lakeville, MA
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
F1-1 and F3-1 error code
Very easy to repair, but you have to be able to pull your stove out. Two screws in the oven and then remove part of back cover of oven and one plug from there. Simple to do, but did not fix our problem. We are waiting repair now from service company as it looks like it needs a control panel. Worth trying yourself to fix the problem. Inexpensive part and easy to install. Also be sure to turn power off your oven to reset the control panel as this may fix the problem - try this first and also after installing new part - like rebooting a computer...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Glencoe, MN
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Top oven element works, but bottom element works only intermittently
Replaced the long Oven Sensor but have not resolved the root problem. Oven still will not reach required temperature. Bottom element becomes red hot, but turns off and will not start again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- patricia from chipely, FL
- Parts Used:
- WP355214
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
door of oven came apart when plastic screw holders broke
put back together with parts ordered. Parts arrived in 2 days!!!! and saved my large dinner party the following day from being ruined. Thank you so much for your parts inventory and for Jenn Air supplying only the part needed and not the entire door. It was a life saver!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Chehalis, WA
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
burned up switch
Opened the back of the cooktop and found upper right element control switch burned. I removed the retaining screws and wires and spent two weeks chasing the switch at a local dealer. Found exactly what I needed at PartSelect.com and paid less even with shipping than at the local. Installed the switch with original screws and presto!! it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from Colorado Springs, CO
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Burner would not turn off
It was easy enough I unplugged the stove. removed the screws under the control panel,removed the panel, removed the two screws holding the switch in place. moved the electrical wires from the old switch and placed them on the new switch. put it all back together in the reverse order.
it took greater than 15 minutes as this is the first time I did any work on my stove and wanted to be careful and not dismantle too much or scratch anything.
it took greater than 15 minutes as this is the first time I did any work on my stove and wanted to be careful and not dismantle too much or scratch anything.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Charlotte, NC
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Burner had one temp. hot
Changed out surface burner switch.Unscrewed two screws, changed plug onto new switch.Don't forget to turn off power!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Wilson, NC
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
not a prblem,just necessary to replace
even though these sre washable filters it's still necessary to change them after so much time
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Temple, TX
- Parts Used:
- W11120791
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
burned burner control out of warranty
switch power supply off at breaker panel
unscrew control box assembly from stove
slide control out of stove
unscrew burner control out of assembly
transfer wiring from old control to new in same relative location
reassemble in reverse order
restore power
test burner in all positions
unscrew control box assembly from stove
slide control out of stove
unscrew burner control out of assembly
transfer wiring from old control to new in same relative location
reassemble in reverse order
restore power
test burner in all positions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from New Albany, OH
- Parts Used:
- 12001656
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven Over Heating
Removed the oven from the wall. Removed back cover and unplugged sensor from the harness. Remove and replace sensor from inside the oven. Reconnect harness and reinstall back cover. Secure oven back into the wall.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Batavia, NY
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Control switch would not operate
Looked up schematic. Removed 3 screws holding cover. after I shut power off of course. Took off knob. Oriented new control to the one on panel. Disconnected each wire one at at time and immediately attached it to the new control for each wire. Removed screws holding old control and inserted and screwed to the new control and put the knob back on. Put the cover back on. Worked fine. Probably should replace the others as they don't turn as easily as the new one. Probably will spray some contact cleaner which will give me a few more years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from Newton, NH
- Parts Used:
- WP71002111, W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
grease filter did no fit much to large
switch went well
removed 4 screws and lifed front panal up and out
removed 4 screws and lifed front panal up and out
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from Nicholasville, KY
- Parts Used:
- 12001656
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven would not heat
Flipped off breaker and removed oven door and pulled built in stove out so the back panel could be removed. Unplugged the sensor then removed the two screws securing the old sensor inside the oven and installed new sensor. Put stove back together and installed back into counter top, re-installed oven door, flipped on the breaker and oven works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Batavia, NY
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Broken Surface Burner control
Remove 4 screws that holds down panel;removed dial;removed screw that held switch to panel. Took off wire one at a time ann put on corresponding lug. Repeated above in reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Gray, GA
- Parts Used:
- WP71001680
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Bake element need replaceing
5 min. to replace old with new. Remove 2 screws
and detatch wires. Re-attach wires and replace screws. PROBLEM -THE ELEMENT- I recieve had 2 wire legs which hold the element off oven floor, these legs were loosely to element and one came off during installation. OEM had large clamp on legs- I had to remove leg from OEM and attach to
element.( Hacksaw ,file ,vice)
and detatch wires. Re-attach wires and replace screws. PROBLEM -THE ELEMENT- I recieve had 2 wire legs which hold the element off oven floor, these legs were loosely to element and one came off during installation. OEM had large clamp on legs- I had to remove leg from OEM and attach to
element.( Hacksaw ,file ,vice)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from GAITHERSBURG, MD
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
burner control stopped functioning.
Replaced the control.
Was this instruction helpful to you?
Thank you for voting!