JES9860BAS19 Jenn-Air Range - Instructions

I ordered replacement burner cartridge. Pulled out non-functional burner cartridge and installed new cartridge. They are plug in units so no tools were needed and it only took about 15 seconds. Took longer to get cartridge out of shipping container than it did to install it.

New black unit looks different than 15 year old unit but works better and looks better. Black granite appearance is more modern looking.

I should add that the old unit had been in place for approximately 15 years. It didn't come out when I first was trying to remove it to get model number and serial number from it. Once the old rust and corrosion was overcome it removed and reinstalled as easy as any electical plug in a wall outlet.

unscrewed and unplugged the old one and plugged in and screwed in the new one. EASY!

I ordered the door glass from Part Select, which arrived quickly and in good condition. I loosened two sets of screws under the bottom glass holder frame, removed three screws at the top of the door to give more room. Slid the glass in place, re-installed and tightened the screws.The stove door looks great and works great. Great customer service too.

Pulled oven out of the cabinet/wall and pulled sensor out and replaced with new one.

A few years previously I had this same problem and a PROFESSIONAL had replaced the sensor.
Thus this time I knew what the failure was and obtained the sensor from Part Select. Having observed the PROFESSIONAL replace the sensor before; I followed his easy technec only to learn that when the sensor was pulled from the aft wall of the oven that the wires had deteriorated and the plastic plug melted. Therefore it was neccessary to remove the oven from the wall cabinet. Then I removed the panel from the back outside of the oven, cut back the wires and because the kit from Part Select contained additional connectors was able to splice in a replacement connector. Installed the new sensor and reinstalled the oven. LESSON LEARNED; when the PROFESSIONAL had replaced the sensor he had failed to feed the wiring and plug back past the insulated chamber, directly behind the oven, into the cool area assessable by the panel on the aft side of the oven thus the plug and wires were exposed to the heat of the oven. What would commonly be a few minutes job turned into an afternoon project.

Remove and replace with new. No tools required.

This is fantastic. We've had this Jenn-Air range for some time now, but we only used the two-burner module on one side and the indoor grill on the other. Less than a week before Thanksgiving we decided that the extra two burners would be very useful, so I set out to search the internet for a good deal and the possibility of getting it before needed. Then I found your website and within minutes theunit was on the way and, at the most reasonalable price available. I recieved the unit he next day. All I had to do was plug in the module and it was done.
Thanks for making life easy

Removed the old sensor by removing two screws and pulling the wire out through the hole. Disconnected the connector and discarded the old sensor.
Selected the correct connector of the 3 provided, plugged the new sensor in and threaded the wire back into the hole paying special attention to make sure wire and connector was on the backside of the insulation. Assembled the two screws and tightened.

Removed 2 screws holding element to stove then gently pulled element forward to exposed lead connections and disconnected leads to element then reconnected leads to new element and gently pushed element ends back into the openings in the back of the stove and replaced screws to hold element to stove

Our Jenn-Air cook top is 25 years old. One can no longer order parts for this old of model. We ordered new SS burners as well as new Burner cartridge terminal blocks for a new and current model. They work perfectly. Took 10 minutes. $ 350 dollars verses $ 2600 for a new JennAir range plus instillation. Unit looks and works great. Plan to order new switches next.

First, thanks to PartsSelect for getting the part to me so quickly. I went to the "Instant Repairman" , checked all that applied to my problem. The answer was the sensor, 99% of the time.I used a coat hanger to pull the latch back and open the door. I watched the video and followed the instructions to remove the old sensor. The wires were melted but the plug was still good. I used one of the adapters to install the new sensor, then replaced the two screws inside the oven. I pulled the stove out because I had read in the reviews that you needed to get the plug behind the insulation away from the oven wall. I was lucky ,there was a small hole in the back ,right behind the sensor.I gently pulled the wire and plug to the back ,well away from the oven wall. Put the stove back in place ,threw the breaker and was back cooking again!! My stove has a downdraft vent, took me longer to hook the vent back up than to install the sensor..Oh yes, did I say,I am a75 year old female and I did it all myself..

Checked online to see what F3 readout on stove meant. It meant replace sensor. Ordered part on a Sunday and part delivered Tuesday, Monday being MLK day. Detached bad sensor(2 screws inside oven)had to pull new sensor connector through hole from behind as insulation was too heavy (only removed 4 screws on right rear panel.Clipped wires together and reattached sensor inside oven. A cakewalk.

Was very good. I removed the screws from the switch panel and switch, with phillips screw driver and changed wire connectors from the old switch to the new switch and installed new switch in the front panel and reinstalled the panel.

I ordered the part one afternoon. It arrived before noon the next day. Then I simply removed the old seal (with about 2 dozen spring clips). Inserted the new part by carefully inserting the new seal into its corresponding hole at each end and then worked my way around the seal while inserting each attached spring clip into its corresponding hole.

Each cartridge unit consists of two electric coil burners in a larger frame assembly. The old cartridge units simply lift up and unplug from the range top. The new units simply plug in and drop into place. It probably took more time to unpack the box than to remove the old, and insert the new cartridges. Anyone can make this repair, which instantly converts an old range top into a new one.