JES9860BAS19 Jenn-Air Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- valerie from lanoka harbor, NJ
- Parts Used:
- 74003645
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
inner glass on oven door cracked.
Repair was very simple. Took the door apart in layers, replaced the glass and put everything else back. it took longer to clean the stove than it did to actually take it apart and put it back together. guess i didnt need to be that much of a clean freak!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Athens, OH
- Parts Used:
- 74003645
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Glass on inside of oven door cracked
I took the oven door apart, pulled out the broken fragments of glass and replaced it with the new glass. I should have taken notes as I took the door apart because it was a bit tricky to remember how all the pieces fit back together.
I was very impressed with how quickly the parts were shipped and the quality of the packing materials to protect the glass as it was shipped.
I was very impressed with how quickly the parts were shipped and the quality of the packing materials to protect the glass as it was shipped.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marion from Center Point, IA
- Parts Used:
- JEA7000ADSA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cartridge was in need of replacement unit
Unplugged unit,cleaned stove and replaced new cartridge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pamela from Kerrville, TX
- Parts Used:
- JEA8120ADBA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Old stove burners were rusted out and hard to clean
Unplugged old units and plugged in new units. They fit perfectly and it was all so easy. I have been very happy with PartSelect services.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebecca from Simpsonville, SC
- Parts Used:
- JEA8200ADX
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original non stick griddle was scraped and used.
Just removed olriginal griddle and ireplaced new one. No tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Geri from El Dorado, CA
- Parts Used:
- JEA7000ADSA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
part was just looking old and worn
Really simple just had to remove the old part by simply pulling it out of the socket and then insert the new cartridge. It looks great it was shipped in a matter of days I was surprised to get it so soon.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wendel from Marietta, GA
- Parts Used:
- JEA7000ADSA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burners not working
Plugged it in. It was that simple!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Brandon, WI
- Parts Used:
- JEA8120ADBA
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
One burner ,of a 2 burner cartridge, was burned out. I called an appliance dealer. no help. Went on line, typed in Jenn-air cooktopand several choices came up. Clicked on yours, went thru about375 parts. Spotted what I thought was was the right one. Called in. It had three flat prongs and one ro
I lifted the old old cartridge on one end and slid it out. Then I shoved new cartridge in place, tried the burners. Perfect! Saved me from getting a entire new cooktop. Would recommend PartSelect to anyone looking to repair an old stove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mark from CHAMBERLAIN, SD
- Parts Used:
- 12001656
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
my oven would not heat to proper temp
I slide the range out and unplugged it from the outlet. I removed the back of the oven ( 8 screws ) using a cordless drill and phillips bit then with a phillips screwdriver I removed the oven sensor (2 screws) then I installed the new sensor , reinstalled the oven back , plugged the range in , slide it back into place and that was it. This repair took about 10 mins and the oven works perfectly. Thanks !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Katy, TX
- Parts Used:
- WPW10162384
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Needed to replace the oven door gasket/seal
Removed door from oven by pulling up at the first stop point after opening the door. Removed the outer shell by removing 5 screws. Disassembled the inner door by removing 6 screws. Be careful with the insulation blanket (fits in a molded portion of the inner door). Glass windows can be removed (for cleaning) via a couple screws. Old gasket/seal is held in-place via spring-clips; just squeezed each clip, pushed each thru their respective holes, and pulled off the worn-out gasket. New gasket snapped in-place by pushing the clips thru the respective holes. Reverse the process to reassemble the door. You can do this job in 15-20 minutes. Took us longer because it took some elbow-grease (and patience) to clean the crud off the glass windows.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harlen from Spring Creek, NV
- Parts Used:
- WPW10162384
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door gasket was hard and brittle from baked-on grease - heat leaking around door
Waited for my husband to do it, but when he didn't, I tried it. Very simple! Just pulled the old gasket out of the pinch pin holes in the door, then replaced it. Tuck the one end into the hole at the bottom of the door, then match up the little pinch pins on the gasket with the holes in the door - matches up perfectly! Be sure to tuck in each of pinch pins till they sort of "snap" into each hole. Took me 5 minutes, tops. Works great now, no more lost heat around the edge of the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Geraldine from Germantown, NY
- Parts Used:
- WP7801P173-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Racks were dark and dirty
The first set of racks did not fit. I called the Service rep, gave him the model number and exchanged the racks for the new ones. The new ones fit perfectly and the service was excellent. I would definitely recommend PartSelect.com to anyone who wants to deal with a company with excellent service, parts and representatives who know their stuff.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Trace from Ofallon, MO
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven was not correctly heating to set temperature
Removed the approximatly 10 screws that hold on both the upper and lower pieces of sheet metal that cover the back of the oven. Removed the screw holding in the temp sensor. Unplugged and removed the old sensor. Plugged in and installed the new sensor (using one of the included adapter wires supplied with the sensor). Put the 2 pieces of sheet metal back on and plugged in the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Brighton, MI
- Parts Used:
- A341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cooktop/grill scratched up
I bought 2 covers, they are great, I can put them on and the cook top looks wonderful. I bought an older home and the Jennn-Air top was scratched up, now you cant tell at all when I put the covers on. I was thrilled to find them. I thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adam from modesto, CA
- Parts Used:
- 74003645
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
broken oven door inner glass pane.
Remove the door, remove screws from all sides
Remove sides and face of oven door by sliding down from under the oven handle trim.
Remove screws on 2nd light of glass and set aside.
Now you are at the inner door panes. their should be two in an insulated type unit.
Remove the remaining screws from the handle pracket and the permiter frame for the glass/insulation. Remove permiter frame and set aside.
Pull out inner door glass frame. get a pair of pliers and bend tab on frame up so you can pull the frame sightly apart, replace the glass, secure frame tightly around glass slide tab back into reciever slot and bend down ( you may need another person to assist in keeping both lights in the frame while trying to ben tab back in to place)
reassemble door as it came apart carefull not to over tighten the screws, they strip easy.
Remove sides and face of oven door by sliding down from under the oven handle trim.
Remove screws on 2nd light of glass and set aside.
Now you are at the inner door panes. their should be two in an insulated type unit.
Remove the remaining screws from the handle pracket and the permiter frame for the glass/insulation. Remove permiter frame and set aside.
Pull out inner door glass frame. get a pair of pliers and bend tab on frame up so you can pull the frame sightly apart, replace the glass, secure frame tightly around glass slide tab back into reciever slot and bend down ( you may need another person to assist in keeping both lights in the frame while trying to ben tab back in to place)
reassemble door as it came apart carefull not to over tighten the screws, they strip easy.
Was this instruction helpful to you?
Thank you for voting!