SVD48600BC Jenn-Air Range - Instructions

I didn't. Don't know how to get to light bulb to change it for this specific model

The repair for the glass on the inner door of the oven was very straight forward and easy. All I did was remove the door from the oven and then systematically took apart the door. I did not have any schematics, but if you just look at it you can figure out what you need to do. Once apart I had to use pliers to bend the metal that was holding the glass in place and then I simply installed the new one and put everything back together. The whole process took maybe 20-45 minutes from start to finish. Now I can bake a Turkey for Thanksgiving...YEAH!!

pull oven, remove back pannel and unplug and remove high limit switch. Repair was the reverse of removal.

Removed the approximatly 10 screws that hold on both the upper and lower pieces of sheet metal that cover the back of the oven. Removed the screw holding in the temp sensor. Unplugged and removed the old sensor. Plugged in and installed the new sensor (using one of the included adapter wires supplied with the sensor). Put the 2 pieces of sheet metal back on and plugged in the oven.

I inserted the door strikes in the proper position and then snapped the panel in place.

None of the surface burners (two Uni-burners) would light without using a match. I first ordered two replacement PS2089818 top burner spark electrodes. I replace one which was very easy - the electrode just clips into the burner - and I traced the wires down to the back bottom of the stove where I found they plugged into an ignition module. The new electrode didn't help, but since all four burners were out it made sense that the ignition module would be the problem and not the two separate electrodes. So I ordered a new ignition module. It plugged in easily with the terminals well marked like the original. I put the original electrode back in and all four burners now light properly with the desired "tic tic tic" sound with the knobs in the "high/light" position.

The video indicating •unscrew old sensor, •pull wiring, •unplug old sensor, and •plug in replacement was good until I pulled the old one and saw wire nuts behind the small square hole! After some research, I learned that the nuts COULD come through that small hole with use of needle nose pliers. One of the wire nuts had the edges pinched off (chipped) in the process. Then I learned about ceramic wire nuts, which I'd never previously encountered. Very important if you don't want to melt your nuts! I cut and stripped the end of a disconnect plug to the stove wiring and now I have a plug in place; which, hopefully, I'll never need to use.

We operated the oven without the display panel for three years and finally discided to get it repaired. The cost of the repair was going to be over 330.00. I went online to PartSelect and had the part in a few days. I removed the 4 front screws behind each of the knobs, next I removed the 4 screws and 4 hex bolts under the front panel. The two side panels needed to be removed by taking out the screw from under each panel. Remove the front control panel and release the ribbon cable by pressing in on the two side tabs allowing the locking connector to be rasie up relaseing the ribbon cable. The other two power cable can be gently removed. Two hex bolts hold the disply panel to the front panel. Installation is the reverse of the removal process. The process took less then 20 minutes. PartSelect customer service was very professional and I will use them again without a second thought.

I rremoved two screws and pulled element out about 3 inches. I un hooked the two wires and tested with an ohnm meter to determine the condition of the element. Element was bad so I ordered a new one. Service and price were great. Easy fix. Thank you.
Don't forget to unplug first.

Replace filter

The door seal was an exact fit for the factory one. There are little clips that hold the seal to the door. The clips are already installed in the seal. To remove just grasp the seal at each clip and pull up. The seal comes off easily. The ends of the seal are tucked into holes at the bottom of the door so you can just pull them out. For the installation of the new seal grasp the seal at each clip and push them into the littles holes. I used a flat blade screwdriver to tuck the seal ends into the two larger holes at the door bottom. The whole process took about 10 minutes.

I wouldn't have changed the seal but the hot lasagna made the seal sort of hard after it cooled off.

After turning off the circuit to the oven, I first removed the 6 exterior screws holding the upper unit that houses the clock element, then I disconnected the three wiring connectors. The difficult one is the ribbon connector. You must push in the two clips on the end and then raise one side of the connector in order to have it release the ribbon. then I removed the 4 screws that hold the element. You then just put the new one on in reverse of removing the old one. It works great. This could be made easier if each new unit came with visual picture instructions for removing the ribbon cable connector. I read all 14 previous customer reviews or stories, before I found one nice guy that described the proper method of removing this ribbon. Thanks

First I turned the power off to the stove at the breaker box. I opened the oven door and took off the four hex head screws holding the face panel on. There are four philips screws holding a trim piece on the panel that does not need to be removed and the two end caps do not need to be removed either. I pulled the panel out and tipped it up so I could access the clock display unit. There are two wiring harness clips that unplugged very easily. The ribbon connector is a little more tricky. You have to slide up two clips on the end and then slide up a section going across the ribbon. It's very easy, just don't try to pull the ribbon out without undoing the clips. The display unit was held on with two hex head screws. I removed them, attatched the new one and put it back together. I then turned the oven back on to see if it worked. The display worked perfectly but, the oven would still not get hot on bake. I turned the breaker off again and removed the shelves in the oven. I then removed the two phillips screws holding the bottom bake burner in and pulled it out until I could access the clips. I pulled off the clips and checked the burner for continuity. There was none so I ordered a new bake burner. The new burner showed up the next day and I hooked it up in about 5 minutes. The oven works great and I couldn't be happier with the experience I had with partselect.com

Turned off the breaker to the stove and removed the 4 screws under the control panel. The trim strip and the end caps did not have to be removed. The control panel was lowered just enough to clear the upper edge and then tilted forward so the connectors could be disconnected. Two screws holding the display in place were removed and the new display swapped out. Reassembly was disassembly in reverse. (My wife appreciates having a bright display again.)

Unplug and pull range away from wall.
Remove metal panel from back of range by using nutdriver to remove 4 screws.
Use phillips scewdriver to remove 2 screws holding old spark module.
Unplug 4 wires from spark module and note placement of wires for reinstall.
Install new module by reversing procedure.
Slide range back against wall and plug in.

Entire process took less than 30 minutes.

NOTE: Spark Module received from partselect.com did not match old part exactly. The screw holes on the new part did not line up with screw holes from old part. I reinstalled new part with just 1 screw. Was told by partselect customer service that the part I received had been substituted and would work fine. It does work but it did not fit correctly.