SVD48600BC Jenn-Air Range - Instructions

unplug the oven and pull it away from the wall. looking at the oven from the back, the spark module is at the bottom on the lower left. there is a two piece sheetmetal cover over the area of the spark module. use a phillips head screwdriver to remove five screws and the covers come off. the spark module is the blue cube with four push on wire connectors. all you have to do is hold the new one next to the old one and swap one wire at a time. both were clearly marked with identical numbers and letters. really nothing to it. it took me longer to clean the back of the oven than to replace the module. the old module was eaton part number Y-54052-3. the new one is eaton part number Y-054052-34.

replaced broiler element - still would not heat.
Called repairman and the control panel is out and will cost around 200.00 to replace. To replace the element, my son helped as my arms weren't long enough. Removed two screws at back and two screws on front of broiler brace. Pulled out and removed wires and hooked them to the new element. Had to turn off circuit breaker. Pushed element back into the holes and replaced screws.
In this instance, it would have been cheaper had I just called the repairman first. However, I have an extra broiler element in case it goes out again.

I was told by appliance repairman that sensor and electronic panel were out - so ordered both as PartSelect was less expensive (about 1/2) than service call price. Sensor was in stock and arrived in 2 days, panel was special order from factory.
Replaced the sensor. Pressed Control Lock pad for several seconds and oven clock came on. Was able to set baking temp, broiler, and convection operation as normal.
Canceled order on panel as Sensor fixed my problem.

The problem was easy to find since the board had caught fire and you could tell which board was bad. I had to remove the protecting jacket. Then removed two screws. I disconnected and reconnected the wires one at a time so I could tell where they went.
The hardest part was pulling the stove out and cleaning the dust and split food.

Purchased 2 piece broiler pan from this site

Diagnosis is the important aspect. Ovens have plunger-type switches to tell the "brain" door is closed, both for the light AND to allow initiation of self cleaning. Finally discovered one of those switches was "scratchy" in operation and unreliable in closing the circuit. (Push the plungers in and out several times and observe the light.) If not 100% reliable, replace that switch (cheap and easy with a Phillips screwdriver.) Initial guess was a $major "brain"-electronics problem but it was merely a sticky switch. Strange since the unit is about a year and a half old and rarely used. Found the part easily with PartSelect, and it came via UPS quickly.

SHUT OFF BREAKER FOR OVEN! pulled oven out to get at backside,removed 3 screws on back coverplate,removed 2 screws inside oven at sensor in top left corner of oven,disconnected plastic clip at back ,pulled old sensor through hole.replaced sensor with new in reverse order. 15minutes tops.

In oven I unscrewed orfice; replaced with new orfice. On stove top the people who make it sent a kit for $11.00, plus S & H. I installed it as per instructions.

I screwed the light lens into the socket and went beautifully. Better than the original. (I am a retired, 75 yr. old woman).

We turned off the stove at the breaker panel. Took off the front top panel of stove and replaced the replacement board. It had three attachments to plug in. We then replaced front panel and turned on the breaker. The stove worked perfectly. It is very nice to have a clock and temperature reading visable again. Part Select was very easy to order from and we received our part within a couple of days. Will certainly suggest them to friends and will use them again.

The first thing I did was to turn off all of the power to the range. Then, I removed all of the screws and unhooked the front panel from the range. Then, I rolled the front panel upside down to get access to the wires. I then proceeded to disconnect all of the wires. After that, I removed the circuit board from the panel. Obviously, I just had to reverse the procedure to install the new circuit board. It was one of the easiest jobs I have had to do.

Removed 4 screws holding trim panel in place. Removed 4 screws on underside of clock panel

Pulled panel out slightly and disconnected the 2 electrical strips

Removed 2 screws holding clock assembly

Disconnected the ribbon circuit tape-push down on the holder tabs and simultaneously pull up gently on trhe ribbon.

Connect ribbon to new unit. Screw unit to panel.
Reconnect electrical strips and reinstall in reverse of disassembly.

Very easy to accomplish

Stove is over 16 years old. I am getting new kitchen in the summer, did not want to buy another stove! I looked on line and found how easy it was to replace element. We turned off power as suggested and removed element to make sure it matched the one on line. I ordered element on Sunday afternoon and it arrived Tuesday afternoon, FedEx ground. Insert the clips and a couple screws and we were having oven fries for dinner. I could not be happier and pretty darn proud of myself for saving a couple hundred dollars on a repair man!

Piece of cake. First, turn off the power to the stove. Then, I removed four hex head screws on the bottom (above the oven door) and four phillips screws underneath the burner knobs (knobs pull right off). The entire assembly then came loose and I laid it facedown on the stove top. The clock control was easily accessible. I unplugged two electrical connections and a ribbon which "unplugs" easily by squeezing the ends and pulling up on the ends. Only two hex head screws hold the clock assembly and I removed them.

Then, it was only a matter of reversing everything I had done. The new clock light is brilliant.

However, I was very happily surprised how fast I got the part even though I did not specify fast shipping.