SEG196-C Jenn-Air Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Edwin from Shalimar, FL
- Parts Used:
- 12200039
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The old switch disintegrated
Disconnected power from the stove. First I removed the down draft vent cover on stove top, then the two screws that held the switch plate in place, then used a wood chisel to pry the switch housing retaining washers off. Removed the remains of the old switch, Installed new switch, attached wires, and reinstalled switch plate. Placed vent cover on stove top and reconnected power.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raul from Tampa, FL
- Parts Used:
- 12200030
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
replace old parts
Nothing really. Only couple of screws to attach the bracket holding the front and back burners.
The other parts: filter, burner, pan, where just replaced.
The other parts: filter, burner, pan, where just replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from Columbia, MO
- Parts Used:
- 12200039
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Togle switch that turns on the fan or oven light was broken
Turned of electrical power. Loosen two screws that held the stove top part that held the switch. Disconnected the old switch by removing the two clamps that held it in place, made sure wires were connected correctly on the new switch and used the new clamps to attach the switch in place. Put everything back together and turned stove power back on. Everything worked as it should.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from BEND, OR
- Parts Used:
- WP71002111
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Grease filter needed replacing.
Removed old filter and replaced with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruth from Gastonia, NC
- Parts Used:
- 866294
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Range oven door switch need replaced
I raised the top of my Whirlpool Continuous Cleaning Canning Oven, then had to unscrew 3 screws and a lock nut, then raise top about 4 inches, so I could put my hand inside to unplug the wires to the switch, and push it through the hole in front, of oven. Then put the new switch through hole and plug in new switch. Then screw down top; and close lid. Part #866294
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Poulsbo, WA
- Parts Used:
- WP7505P283-60, 74005189
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
One 25 yr-old burner was beginning to leak gas because of corrossion. Decided to replace all 4 burners.
Remove grates and pan. unscrew each burner from the metal cross mount bar, keeping in mind, the position of the cross mount bar.(Mine was not reversible.) Reverse the procedure with the new burners.
Adjust the air opening to eliminate any yellow flame. The air opening is located immediately adjacent to where the burner pipe goes into the cooktop. (Near the front of the cooktop in my case.)
Biggest problem was making sure the correct parts were ordered.
Adjust the air opening to eliminate any yellow flame. The air opening is located immediately adjacent to where the burner pipe goes into the cooktop. (Near the front of the cooktop in my case.)
Biggest problem was making sure the correct parts were ordered.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from WESTFIELD, IN
- Parts Used:
- WPY704918
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken gas valve knob
I pulled of the knobs and put on the new. Simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from CARMEL, IN
- Parts Used:
- WP71002111, 8009
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
replaced grease filter
took out old one and after straightening out the significant bends in the metal frame holding the screen, that were caused by shipping the screen in too flimsy of a container, I installed this into the range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Marshall, MN
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
filter was deteriorated from 15 plus years of use
lifted the top center panel off removed old filter installed new easy peesy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from STAUNTON, VA
- Parts Used:
- WP71002111
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Grease filter clogged and in need of replacement
EXTREMELY simple - drop in. AND- the part cost less than half the price quoted by appliance vendor...2 years earlier !!! This site is a marvelous resource for parts one can install with minimal skill.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rudy from GARIBALDI, OR
- Parts Used:
- WP71002111
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old one was plugged
Pulled out old one and slipped in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobby K. from Huntsville, TX
- Parts Used:
- Y704660
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Needed replacement oven rack.
Part was perfect fit. Good product, good value, great service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Whitefield, ME
- Parts Used:
- WP7505P283-60
- Difficulty Level:
- Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
tube was rusted out
just removed two screws - took old unit out - put new unit in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neil from Winchester, VA
- Parts Used:
- 12200039
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
fan/light switch was melted due to a hot pot placed on top.
removing the vent grid on top, by lifting off, then taking out the filter screen. removed the 2 screws on the back of the switchplate, then slide it back. made a drawing of the color wires and which way the switch faces... (it matters)
I took off the the old press-nuts by just breaking them with needle nose pliers. removed the old switch, fitted the new one (paying attention to where the little prongs and big prongs were on the old switch. used the nut-driver to press on the new nuts that came with the switch, and hooked back up the wires, and put it back.
I took off the the old press-nuts by just breaking them with needle nose pliers. removed the old switch, fitted the new one (paying attention to where the little prongs and big prongs were on the old switch. used the nut-driver to press on the new nuts that came with the switch, and hooked back up the wires, and put it back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Frankfort, KY
- Parts Used:
- W11117769
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Renters removed leveling legs from refrigerator. I don't know why!
I tilted the unit back enough to scew the new legs into the threaded holes.
Was this instruction helpful to you?
Thank you for voting!