Models > SEG196-C > Instructions

SEG196-C Jenn-Air Range - Instructions

Jump to:

All Instructions for the SEG196-C
106 - 120 of 209
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Ronald from Rochester Hills, MI
Parts Used:
12200039
Difficulty Level:
Very Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set
Replaced the light /oven rocker switch
The two mounting clips supplied with the switch would not fit onto the two studs in the die casted plate (too small) . In removing one of the old clips, the stud broke off. Thus I had to break off the other stud and drill out the area to allow two screws to be inserted to mount the switch securely.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Alan from Pleasant Hill, MO
Parts Used:
12200039
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Downdraft fan would not operate with light/fan switch.
Removed old switch, but when I tried to install the new one the round slide on retainers that hold the switch in place were cheaply made and broke. I had to go to the hardware store to find replacement parts. Electric terminals matched correctly and slipped off and on just fine. New switch works great.
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sarah from Albany, GA
Parts Used:
WPY702338
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
worn door seal on oven
takes two people to put the oven door back in place but otherwise very simple as long as you keep all your screws and pads in place
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joseph from East Greenwich, RI
Parts Used:
WP71002111
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
replaced the current warn-out grease filter
removed the old by pulling it out of track and replaced it with the new filter
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
james from chapin, SC
Parts Used:
WPY704918
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Broken valve knob
Placed new knob on valve stem
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Chris from Wellesley, MA
Parts Used:
12200039
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers
Old switch was difficult to remove and the push nuts provided with the new switch were too small to fit on the lid posts.
Removed the old switch by essentially destroying it with a screw drive and pliers. Had to drive to the hardware store to purchase push nuts that fit.
.
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ivanka from Atlantra, GA
Parts Used:
8009
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
burned oven bulb
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.
3 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Cindi from Kettle Falls, WA
Parts Used:
WPY704918
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
broken valve knob
Removed old broken valve knob (shaft was split) and pushed on the new knob. It took a little bit of effort to push on the new knob as the shaft seemed to be slightly smaller. Otherwise, very easy. No tools needed.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Barbara from Hubert, NC
Parts Used:
WP71002111
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
needed new grease filter
It was hard. I simply replaced the old one!! fIT PERFECTLY.
:-)
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Donald from Cottage Grove, OR
Parts Used:
WP71002111
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Had to replace grease filter
Nice filter. Exact fit. Had a little ring to use to pull out to clean. Shipment was packed well.
1 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
judy from clifton park, NY
Parts Used:
WP7505P283-60, 74005189
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
it was painless
just as stated before. Remove old burners from plate and reattach new burners.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from Schwenksville, PA
Parts Used:
8009
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
oven light burnt out
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
3 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
lenny from east freetown, MA
Parts Used:
WP7505P283-60, 74005189
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
simple swapping of parts
Undid the bad part and installed the new one
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Clark from Tifton, GA
Parts Used:
WP7505P283-60
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Burner wouldn't light.
Took out a couple of screws and put in the new part. PartSelect was fast and efficient. Highly recommended.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Janet from Ada, MI
Parts Used:
8009
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
light bulb went out in my oven
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.
2 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the SEG196-C
106 - 120 of 209