SEG196-C Jenn-Air Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- mohd fouad alahdab ruh from JAMAICA, NY
- Parts Used:
- WP74003387
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Socket set
The oven light went off, changing the bulb did’n’t solve the proble, beacause the socket was burned.
First thing
disconnect from electricity
Remove the back cover by unscrewing its fixing screws
Using philips screw driver, To remove the scocket assembly, pull the tow electric wires from the socket, using a fine plier.
Open the oven door and unlock the glass cover and remove it.
Remove the 2 screws fixjing the socket from inside the oven.
Now the socket is ready to be disassembled by just pushing the clips with tow fingers.
Replace the socket and do same steps in reverse way.
insert the lamp, and the glass cover, connect the electricity and you are done.
disconnect from electricity
Remove the back cover by unscrewing its fixing screws
Using philips screw driver, To remove the scocket assembly, pull the tow electric wires from the socket, using a fine plier.
Open the oven door and unlock the glass cover and remove it.
Remove the 2 screws fixjing the socket from inside the oven.
Now the socket is ready to be disassembled by just pushing the clips with tow fingers.
Replace the socket and do same steps in reverse way.
insert the lamp, and the glass cover, connect the electricity and you are done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from COLORADO SPGS, CO
- Parts Used:
- WP7505P283-60
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Front burner would not light
Removed old burner, replaced with new one, works perfectly! Only one screw to take out and use with new piece.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Silver Spring, MD
- Parts Used:
- WP705105
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
to convert a cook-top stove with 2 burners and a side grill into a 4 burner stove.
Replacing the side grill burners was easy--lift off the grill covers and pull out the grill burners. Next, attach the new front and rear burners to the burner plate with 2 screws (the older version uses 4 screws) using a nutdriver. Place the 2 burner unit (now joined) into the 2 gas inlets (no screws necessary--just slip them over the tubes). Insert the grill pan over the burners and place the 2 burner grates over each burner. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from Mulkeytown, IL
- Parts Used:
- 703917
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken temperature knob on my oven
This was obviously not a hard repair, I just replaced the knob. I would like to say that I did receive the part in just a little over 24 hours. That was nice!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from Chapel Hill, NC
- Parts Used:
- Y702615
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic lens broken... pilot light not very visible
Shut off power to range. Removed 4 phillips screws under control panel. Tip bottom of control panel up and out to unhook it from the range top. Remove half of old lens piece from slot in bottom of plastic lamp fixture. Insert smaller end of new lens through front of control panel hole. Slide lamp fixture slot over the inside end of lens until it clicks into place. Replace control panel. That's it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Wilmington, DE
- Parts Used:
- 12200039
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Switch for fan was heat damaged and broke
Removed top plate, disconnected old switch... Had to go to hardware store to get different push washers - the ones supplied with the part were too small. connected switch... tested connections and replaced top plate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from Palm Coast, FL
- Parts Used:
- WP7505P283-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
didn't ignite gas range.
After getting help from customer support, I was able to order the part. I tracked the part on FED EXp.
After deliver the part was installed and working in 5 minutes. All that for less than $50.00.
After deliver the part was installed and working in 5 minutes. All that for less than $50.00.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Burma from Section, AL
- Parts Used:
- 3401X055-09
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The painted finish on the pan for my range started flaking.
Called Parts select and they replaced it in two days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Portland, OR
- Parts Used:
- WP7505P283-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Front burner inoperative
Simply removed the front burner using 1/4 incn nutdriver on
two screws.placed new burner in position and tightenwd two screws.
Simplest and easiest job I ever did!
Works as new!
two screws.placed new burner in position and tightenwd two screws.
Simplest and easiest job I ever did!
Works as new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grady E from Vidalia, GA
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed Replacement Filters
Remove Vent Cover, Remove Old Filter, Replace With New Filter, Replace Vent Cover, Repair Complete
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen D from Columbia, MD
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
time to replace the filter
lift out old filter, wash, put in new filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John H from Newfoundland, PA
- Parts Used:
- 74005189, WP7505P283-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Burner Ports were worn and oversize
Removed the two screws that hold burners on mounting bracket . Removed burners and installed new burners. re-adjusted air flow to elimenate yellow flame.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Preben from Fox River Grove, IL
- Parts Used:
- WPY704513
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The stovetop gas regulator kept clicking in off position.
The spare part came within two days after I place the order on line. I drew a simple wire diagram of the faulty switch-regulator. Shut off the power to the stovetop, before removing the four terminals on the faulty switch-regulator. I pushed the old regulator up from the center pin and replaced it with the new regulator. The next step was to reinstall the four wire terminals using my wire diagram. Final step was to turn the power back to the stovetop and test the new switch-regulator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janice from Pawtucket, RI
- Parts Used:
- Y703673
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
After a lighting storm the oven would not work it kept blowing the range fuse it was determined by a friend it ws the selector switch
first removed the four screws that held the panel in place, tthen unscrewed the actual switch itself. I then pulled the wire, one at a time from the old switch and pluged the wire in to the new switch. upon completion I tested the oven selector switch and secured the switch in place, then replaced the panel. And I'm up and running again!
Was this instruction helpful to you?
Thank you for voting!