SVE47600W Jenn-Air Range - Instructions

First I removed the two screws that hold the bake element. I then pulled it out far enough to disconnect the two wires, and reversed the process to connect and secure the new element. I then removed the screws located under the control panel that held it in place. I removed the wiring, 3 cable connections, from the clock circuit board, and the two screws holding it in place. I installed the new circuit board, and reconnected the wiring, and returned the control panel to its place. The wife was upset that she had offered to do some of my chores while I fixed the oven when she found that it had only taken me 10 minutes to make the repairs. The parts were a perfect match, and the job couldn't have gone any smoother.

The problem was easy to find since the board had caught fire and you could tell which board was bad. I had to remove the protecting jacket. Then removed two screws. I disconnected and reconnected the wires one at a time so I could tell where they went.
The hardest part was pulling the stove out and cleaning the dust and split food.

I was told by appliance repairman that sensor and electronic panel were out - so ordered both as PartSelect was less expensive (about 1/2) than service call price. Sensor was in stock and arrived in 2 days, panel was special order from factory.
Replaced the sensor. Pressed Control Lock pad for several seconds and oven clock came on. Was able to set baking temp, broiler, and convection operation as normal.
Canceled order on panel as Sensor fixed my problem.

replaced broiler element - still would not heat.
Called repairman and the control panel is out and will cost around 200.00 to replace. To replace the element, my son helped as my arms weren't long enough. Removed two screws at back and two screws on front of broiler brace. Pulled out and removed wires and hooked them to the new element. Had to turn off circuit breaker. Pushed element back into the holes and replaced screws.
In this instance, it would have been cheaper had I just called the repairman first. However, I have an extra broiler element in case it goes out again.

Purchased 2 piece broiler pan from this site

The F7 code meant that a button was stuck. I removed the 4 front panel knobs then removed the 8 screws that held the stovetop controllers. Then I carefully removed the ribbon cable from the display assembly. I then reassembled the in reverse order on the new part.

I took out the side of the cooktop that did not work. I had to take off the bottom of the cooktop and checked where electricity was going and not going. Once I found the part that needed replacing, I went on the website, search for Jen-Air cooktops and model number. From the sketch on the website, I was able to order the part needed. I decided to get 2 in order to replace both parts at one time, just in case. The part arrived quickly and was easy to install. The most time I spent was taking the backside off the cooktop and cleaning it.

SHUT OFF BREAKER FOR OVEN! pulled oven out to get at backside,removed 3 screws on back coverplate,removed 2 screws inside oven at sensor in top left corner of oven,disconnected plastic clip at back ,pulled old sensor through hole.replaced sensor with new in reverse order. 15minutes tops.

Diagnosis is the important aspect. Ovens have plunger-type switches to tell the "brain" door is closed, both for the light AND to allow initiation of self cleaning. Finally discovered one of those switches was "scratchy" in operation and unreliable in closing the circuit. (Push the plungers in and out several times and observe the light.) If not 100% reliable, replace that switch (cheap and easy with a Phillips screwdriver.) Initial guess was a $major "brain"-electronics problem but it was merely a sticky switch. Strange since the unit is about a year and a half old and rarely used. Found the part easily with PartSelect, and it came via UPS quickly.

I screwed the light lens into the socket and went beautifully. Better than the original. (I am a retired, 75 yr. old woman).

After removing the protective panel from the back, I used one of those screw holes to hold the new mother board right next to the existing one. I unplugged one connection & and plugged in to the new board. A couple of the wires didn't reach, but I committed those to memory. It looks a lot more intimadating than it is. It looks like a bunch of spaghetti, but its easier than it looks and it saved me at least $750

The contact spades were burned from 10+ years of use and the cook top module was worn. I disassembled the module, taped the top to protect the creamic cook top, sanded the metal and spray painted to restore the original white finish. On the bottom half I replaced one missing pop rivet and cleaned and spray painted the bottom to restore to the original black. When the contact spades arrived, I replaced the contact spades and reassembled the module. It now works and looks like it did when it was new.

Stove is over 16 years old. I am getting new kitchen in the summer, did not want to buy another stove! I looked on line and found how easy it was to replace element. We turned off power as suggested and removed element to make sure it matched the one on line. I ordered element on Sunday afternoon and it arrived Tuesday afternoon, FedEx ground. Insert the clips and a couple screws and we were having oven fries for dinner. I could not be happier and pretty darn proud of myself for saving a couple hundred dollars on a repair man!

The first thing I did was to turn off all of the power to the range. Then, I removed all of the screws and unhooked the front panel from the range. Then, I rolled the front panel upside down to get access to the wires. I then proceeded to disconnect all of the wires. After that, I removed the circuit board from the panel. Obviously, I just had to reverse the procedure to install the new circuit board. It was one of the easiest jobs I have had to do.

We turned off the stove at the breaker panel. Took off the front top panel of stove and replaced the replacement board. It had three attachments to plug in. We then replaced front panel and turned on the breaker. The stove worked perfectly. It is very nice to have a clock and temperature reading visable again. Part Select was very easy to order from and we received our part within a couple of days. Will certainly suggest them to friends and will use them again.