SVE47600W Jenn-Air Range - Instructions

A few years previously I had this same problem and a PROFESSIONAL had replaced the sensor.
Thus this time I knew what the failure was and obtained the sensor from Part Select. Having observed the PROFESSIONAL replace the sensor before; I followed his easy technec only to learn that when the sensor was pulled from the aft wall of the oven that the wires had deteriorated and the plastic plug melted. Therefore it was neccessary to remove the oven from the wall cabinet. Then I removed the panel from the back outside of the oven, cut back the wires and because the kit from Part Select contained additional connectors was able to splice in a replacement connector. Installed the new sensor and reinstalled the oven. LESSON LEARNED; when the PROFESSIONAL had replaced the sensor he had failed to feed the wiring and plug back past the insulated chamber, directly behind the oven, into the cool area assessable by the panel on the aft side of the oven thus the plug and wires were exposed to the heat of the oven. What would commonly be a few minutes job turned into an afternoon project.

I did this job myself, but it might be handy to have a helper to assist in holding the control panel during unplug and replug stages of the process. Also strongly suggest you read through these and other posted instructions BEFORE getting started.

Kill Circuit Breaker Power To Unit.
Pull Four Burner Control Knobs off front panel.
Unscrew Phillips Head Screws from under each knob. (Be careful not to strip screw heads, I applied pretty firm pressure on screw driver to avoid stripping).
Open Oven door.
Remove 4 Phillips screws on trim piece under control panel and remove trim piece.
Unscrew 1 small Phillips screw on each side of panel to loosen plastic side trim pieces.
Use socket to remove 4 hex head screws holding control panel in place.
Gently pivot control panel top downward to access the circuit board panel. BE VERY CAREFUL NOT TO ALLOW CONTROL PANEL TO HANG BY FRAGILE CONNECTING CABLES!!!
GENTLY unplug the two white connector cables from the board. There is a locking tab on both that you can release with a fingernail or small flathead screwdriver while gently pulling the connector upward. (These connectors snap to lock more easily when you eventually re-assemble to the replacement board).
VERY GENTLY unplug the ribbon cable. This was a bit confusing to me at first, but if you gently squeeze the two very small tabs on both sides of the black connector, you can gently raise the center body of the connector upwards about 1/8 inch. (You might find it helpful to practice how this mechanism functions on your replacement part BEFORE you do the disassembly, it's really pretty simple once you see how it works). This will take the gripping pressure off the ribbon itself and you can gently wiggle the ribbon out free from the connector taking note of the two very small alignment holes in the ribbon connector as you do so.
Now with all cables free use a socket to remove 2 hex head screws holding the circuit board to the control panel.
Now install the replacement board by simply doing all above in reverse. Take care to line up cable connections to the board properly, noting the two alignment holes in the ribbon cable to tabs in the black connector. All three connections should snap in easily without undue force.
Your range display should be good as new.

Removed the old sensor by removing two screws and pulling the wire out through the hole. Disconnected the connector and discarded the old sensor.
Selected the correct connector of the 3 provided, plugged the new sensor in and threaded the wire back into the hole paying special attention to make sure wire and connector was on the backside of the insulation. Assembled the two screws and tightened.

Our Jenn-Air cook top is 25 years old. One can no longer order parts for this old of model. We ordered new SS burners as well as new Burner cartridge terminal blocks for a new and current model. They work perfectly. Took 10 minutes. $ 350 dollars verses $ 2600 for a new JennAir range plus instillation. Unit looks and works great. Plan to order new switches next.

First disconnected electrical power to range.

Opened the oven door enabling access to bottom of touch pad (membrane panel) front. Removed 4 hex-head screws under membrane panel to free panel from range. Removed 4 surface control knobs then removed 4 surface burner infinite control switches with 4 star-point screw driver (8 screws; 2 per switch). Removed 2 hex-head screws holding clock control. Removed bottom edge strip from under the membrane panel (4 Phillips-head screw driver). Removed both left/right end caps from the membrane panel. Reattached all components in reverse order onto new membrane assembly. Reinstalled new membrane assembly to range.

Reconnected electrical power to range. Tested all components and range is working like new! Other than having an available person to assist in holding panel while reassembling this is pretty much a one-person job. Very common sense steps and relatively easy - even for this woman! Have been inspired to repair timer on dryer.

Actual repair took about 1 hour because I cleaned areas along the way that are normally non-accessible on a daily basis.

First, thanks to PartsSelect for getting the part to me so quickly. I went to the "Instant Repairman" , checked all that applied to my problem. The answer was the sensor, 99% of the time.I used a coat hanger to pull the latch back and open the door. I watched the video and followed the instructions to remove the old sensor. The wires were melted but the plug was still good. I used one of the adapters to install the new sensor, then replaced the two screws inside the oven. I pulled the stove out because I had read in the reviews that you needed to get the plug behind the insulation away from the oven wall. I was lucky ,there was a small hole in the back ,right behind the sensor.I gently pulled the wire and plug to the back ,well away from the oven wall. Put the stove back in place ,threw the breaker and was back cooking again!! My stove has a downdraft vent, took me longer to hook the vent back up than to install the sensor..Oh yes, did I say,I am a75 year old female and I did it all myself..

pulled out the old door gasket, it had little diamond-shaped clips, pulled out really easily, replaced with the new gasket. All the clips fit into the proper holes, stuffed the new ends where the old ones were. Perfect. less than 10 minutes. Thanks....

The replacement switch was not exactly as my original and none of the other instructions matched exactly with my unit. So I had to figure it out, but they matched mostly what Micheal from Colliervile wrote. Safety is paramount. Turn off circuit breaker and ensure there is no power to unit with a test light. You don't have to remove the glass top. Open oven door and remove 4 screws at bottom of control panel, then remove two screws on each end while suppoting the panel with one hand. Rest control panel on top of door or hang by wires. Remove two screws to detach switch from panel. I took pictures of the wire placement on old switch and drew a diagram of what color wire went to each terminal. I used the instruction sheet diagram of new switch and marked where each wire color goes. Here is where I put them: DOUBLE BLACK to L1,2; New jumper from P1 to S1; RED to 2: DOUBLE RED to P2; new jumper with small connector from S2 to "element on" indicator lamp (it's longer than and replaces existing jumper); YELLOW to 4a; TAN to 4. The letters in parenthesis on the instruction sheet almost matched up to my old switch so I used them to help with the placement. I didn't have to seperate any compound red wires. Double check wire placement and put it all back together in reverse order.

Checked online to see what F3 readout on stove meant. It meant replace sensor. Ordered part on a Sunday and part delivered Tuesday, Monday being MLK day. Detached bad sensor(2 screws inside oven)had to pull new sensor connector through hole from behind as insulation was too heavy (only removed 4 screws on right rear panel.Clipped wires together and reattached sensor inside oven. A cakewalk.

First step is turn the power to the range off. Then I removed the grate covering the down draft vent in the center of the cook top. Inside the vent opening are two screws that secure a panel that holds the four knobs that control temperature settings. Remove these screws. Slide the panel tward the back of the range while lifting it up. This will allow removal of the panel. Remove the knob from the burner control you are replacing. Under the knob are two screws. Remove the screws and let the controller drop out of the cover panel. Take the new switch and carefully remove the wires from the old controller and place them on the new controller in the same position. When the wires have been connected, put the controller back in the control panes and secure it with the two screws. Replace the panel back into the cook top. Tilt the control panel so the front is low and the back is elevted. Engage the lugs protuding out on each side of the control panel opening. Lower the panel back into the opening and secure it with the two remaining screws. Replace the control knob and you are done. You just saved yourself a $125.00 service call. Total cost for the controller $35.00.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires to remove the old sensor. Went on line to find out where to order it from. Ordered it, It was on back order but was only about 1 week to receive. Reversed the procedure. WA LA. It works great.

Purchased 2 piece broiler pan from this site

Disconnected electrical power to the range.

Rmoved two burner cartridges. Removed 4 outer hexhead screws around outside metal frame. Removed 5 inner phillips screws holding the furner cartridge pans.Lifted the top metal frame away from the memebrane panel. Removed 4 hexhead screws under membrane panel to free membrane panel from range. Removed the 4 surface ontrol knobs. Remove 4 surface burner infinite control switches. Needed to use a 4 star point driver to remove 8 screws. Removed two hexhead screws holding the clock control element. Removed the bottom edge stripe from under the membrane panel 4 phillip head screws. Removed both left and right end caps from the membrane panel.
Reattached all components in reverse order onto the new membrane assembly.
Reinstalled new membrrane assembly. Reinstalled top metal frame and secured with appropriate screws. Reinstalled top burner cartridges and 4 control knobs.

Reconnected electrical power to the range.

Clock was illuminated. My wife tested all oven and broiler functions including time settings and cancel/off touch button.

As of now the range is working like new.

Before the membrane assembly was ordered, I researched this problem through the Repair Forum. Looked for similar problems from others.
Printed list of all stove fault codes for understanding. Printed parts list for the control panel section to identify all components.

Performed 2 dry runs in disassembling range top for understanding.

Actual repair time took about 2 hours.

Thank you for all the technical information to handle this repair.

Turned the circuit breaker to "off"
Unbolted the unit from its cabinet (4 screws - visible when the oven doors are open - secured the unit in its cabinet)
Slid the unit out of the wall about 2 inches
Removed the control panel.
Unbolted the cooling fan assembly
Unplugged the assembly from the wiring harness
Removed the cooling fan from the oven

Plugged in the new cooling fan
Bolted the new fan in place
Replaced the control panel
Slid the unit back into position
Bolted the unit in place
Turned the circuit breaker back on
Tested

No problems - the hardest part was having to reach to the back of the oven from the front.

First I removed the two screws that hold the bake element. I then pulled it out far enough to disconnect the two wires, and reversed the process to connect and secure the new element. I then removed the screws located under the control panel that held it in place. I removed the wiring, 3 cable connections, from the clock circuit board, and the two screws holding it in place. I installed the new circuit board, and reconnected the wiring, and returned the control panel to its place. The wife was upset that she had offered to do some of my chores while I fixed the oven when she found that it had only taken me 10 minutes to make the repairs. The parts were a perfect match, and the job couldn't have gone any smoother.