J466*03 General Electric Range - Instructions

Turn off electricity to the oven. A socket set was needed for the small screws in my old oven. Once the screws were removed the element came off easily from two wires in the oven. You have to be careful when handling the wires that they don’t fall back into the oven. The new part was attached to the two wires, screws were tightened on the new element and that was it. When the oven was turned on the new element smoked a little but I saw on the video that is normal.

I used a philip screw driver to remove two screws which enable me to pull the wires out about three inches from the back of the oven and replaced it with the new one after disconnecting the wires from the grill. The hardest thing was the limited space.

Turned off breaker,first . Then removed 2 nutscrews and pulled unit out , 4 inches ,removed 2 nutscrews joining the 2 wires and the 2 terminals of the bottom element. Removed bottom unit and replaced with new unit . reversing the process. Turned breaker on and tested the oven. Works fine. Took less than 15 minutes.

turn power off at circuit breaker box, remove old coil from oven, attach the new coil and attach to wall of the oven. Very easy to repair.

First turned off the circuit that controlled the power to the Stove/Oven.
Then I removed the screws that hold the element in place.
I pulled the element out a few inches and disconnected the wires.
I attached the wires for the new element.
I replaced the screws.
I turned on the circuit.

And to reward myself baked a Coffee Cake. Yum!

Removed 2 screws with nutdriver.Pulled element out to expose wiring and disconnect 2 wires also with nutdriver. Reverse process. Unit reaired.

removed the old heating element which had about two screws and two connecting wires and replaced it with the new one. I twas so fast and easy. I thought I was going to need a new Oven!!!!!Thank goodness for your website!!!!!

The repair was pretty easy. I unplugged the stove and took the 2 screws out that secured the element into the back of the stove. I then used a pair of needle nosed pliers to pull the wires off the element that wasn't working and then attached the wires to the new element. I then put the screws back in place securing the element to the stove and it was done. It took me about 5 mintues and the element worked immediately.

The part arrived ahead of time by mail. I removed the old coil, very simple,, I installed the new one just as easy , Turned on oven and it worked prefectly , its a very simple procedure, thank you

Removed 2 screws (with 1/4" nut driver) on bracket holding heat element at back of oven. Pull element forward to expose the 2 wires connected to element, remove screws on wire corrections with flat head screw driver. Remove element from oven......Reverse the steps to install new heat element.....very easy job....except I cleaned the oven while I had the element out of the oven.

remove 2 screws pull out, and had a little trouble with the 2 power lines(breaker turned off), as they were around 60 years old, used a nut driver, and plyers to hold leads, and reversed to install. went well considering the age of the oven. tested, broiler works well,(let it heat up for appx 2-3 min to burn off dirt, etc)

Parts arrived bent and element had tape residue on it. After approximately 1 hr. I was able to clean, make parts straight and install it.

I initially only purchased the heating element since this usually the cause of the broil element not functioning well. It took a little longer to receive because I had to order it over the Holidays. Once it arrived it was very easy to replace. It worked very well after installation but the broil element still did not function. I then purchased the broil element and received it within approximately 4 days. It took just a little more time to replace because there was a brace that was attached to the upper oven that helped to hold it in place. Once the wires were attached with the screws it worked very quickly. It's nice to have my oven back in use again!

The bake element was completely missing from the stove. There were two wires sticking out of the back of the oven, one with a terminal on the end and the other with the insulation still on and no bare wire showing/ The right side mounting screw was there..

The left mounting screw hole on the oven had been drilled out oversized, so I drilled another hole in the mounting plate above the original., after attaching the element with a single screw.

I removed the one screw, removed the bake element and pulled the electrical wire without the terminal end. Next, I put a terminal on the wire and attached the wires to the element. Finally I installed the element with the two screw into the rear of the oven.

Unfortunately the element didn't work, so my next step is to trace the wiring and determine if a switch or thermostat might be faulty. I have checked the continuity of the wires from the bake element to the thermostat.

More in chaper two..

I was worried at being able to locate the part as the oven is over 35 years old. I put in the old part number on your site and it gave me the correct replacement. On my model you unscrew the two screws securing the element to the back of the oven. Then pull out the old element carefully because the wires are screwed onto the element. I pulled it out 4 or 5 inches and unscrewed the wires and connected the wires to the new element. I then threaded the wires back into the hole at the back of the oven and screwed the element back in place. Works perfect.