J466*03 General Electric Range - Instructions

Used socket set to remove bolts holding the elements in place, then used a screw driver to remove the wires from the elements. Replaced with new elements, screwed in the wires and reattached the elements to the wall with the bolts.
It was easy, it was just a small space to work in.

Due to this wall oven being vintage 1972, I decided to replace the broil element along with the bake element that had actually failed. The repair was pretty straight forward as seen on the videos, altough it can be somewhat tight to use screw drivers or nut drivers with long handles. You may find that shorty screw drivers or a 1/4 inch ratchet wrench and appropriate socket are easier to work with. There were two things that I was cautious about. The first was to be very gentle with the power wires since I didn't know what condition their insulation was in. I tried not to scrape them on the sheet metal opening as I pulled them gently out through the oven insulation. Secondly, I was very, very careful in moving the oven temperature sensor probe out of the way so I could undo the broil element. Before I started the job, I had learned that this probe isn't a separate piece part, it is part of the entire THERMOSTAT ASSEMBLY for the stove and it's not readily available. Furthermore, this assembly costs $250 to $350 !!!! The only negative with this job was that the old broil element has some kind of heat resistant material on the rear of the plate that attaches it to the oven wall. This old material fell apart during disassembly. I kind of pieced it back together during assembly, but I would have liked to have been told I needed this piece (since there wasn't an exploded parts view on the web for me to look at)or a new piece of this material should have been supplied as part of the broil element.

replace with new one

Disconnected range from power. Removed small / lower shield that protects element connectors from rear of range. Disconnected the power lines from the element using screwdriver. Removed racks and liner from oven. Removed screws at rear of oven box that hold old element. Removed the old element. Reversed steps to install replacement heating element. Tested oven heating using oven thermometer.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the four wires The element i request was 3 elements and i received two element but it was very easy i connect only the 3 wires.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. connected the wires to the new element. pushed the element back in place the screwed it back to the back of the stove.

Removed the plug from wall socket.
Removed door to oven by lifting it straight up while partially open, in locked position.
Remove Baking shelves.
Removed 2 screws @ the back of element where it goes into the ovens back wall with a nut wrench and gently pull the element towards you until wires are exposed.
Using a flat blade screw driver hold on to the end of the element near the end with the screw and support it as you un screw the wire so the end of the element does not bend as you turn the screw.
After both wires are removed, remove the old element.
Install the new Element in reverse.
Very Easy!

This part has the trim ring attached. My old element had the trim rim detached. This new part still fit my stove top and works fine.

Shut power off. Removed two outer screws, pulled heating element forward and removed two more screws. Ordered part and it arrived in three days. Installed in reverse order of removal. Easy fix. Cost was reasonable.

I initially only purchased the heating element since this usually the cause of the broil element not functioning well. It took a little longer to receive because I had to order it over the Holidays. Once it arrived it was very easy to replace. It worked very well after installation but the broil element still did not function. I then purchased the broil element and received it within approximately 4 days. It took just a little more time to replace because there was a brace that was attached to the upper oven that helped to hold it in place. Once the wires were attached with the screws it worked very quickly. It's nice to have my oven back in use again!

Turn off electricity to the oven. A socket set was needed for the small screws in my old oven. Once the screws were removed the element came off easily from two wires in the oven. You have to be careful when handling the wires that they don’t fall back into the oven. The new part was attached to the two wires, screws were tightened on the new element and that was it. When the oven was turned on the new element smoked a little but I saw on the video that is normal.

Parts arrived bent and element had tape residue on it. After approximately 1 hr. I was able to clean, make parts straight and install it.

Removed 2 screws (with 1/4" nut driver) on bracket holding heat element at back of oven. Pull element forward to expose the 2 wires connected to element, remove screws on wire corrections with flat head screw driver. Remove element from oven......Reverse the steps to install new heat element.....very easy job....except I cleaned the oven while I had the element out of the oven.

The bake element was completely missing from the stove. There were two wires sticking out of the back of the oven, one with a terminal on the end and the other with the insulation still on and no bare wire showing/ The right side mounting screw was there..

The left mounting screw hole on the oven had been drilled out oversized, so I drilled another hole in the mounting plate above the original., after attaching the element with a single screw.

I removed the one screw, removed the bake element and pulled the electrical wire without the terminal end. Next, I put a terminal on the wire and attached the wires to the element. Finally I installed the element with the two screw into the rear of the oven.

Unfortunately the element didn't work, so my next step is to trace the wiring and determine if a switch or thermostat might be faulty. I have checked the continuity of the wires from the bake element to the thermostat.

More in chaper two..

Removed screws that hold element in place. Disconnected the two electrical leads. Put the new element in place, hooked up the two leads and installed the the screws that hold the element in place.