JCKS05GS-1 General Electric Range - Instructions

After turning off power, I removed the two screws and pulled the element and wires out, removed the wires and then attached them to the new element and replaced the screws. However, this did NOT correct the problem. The broiler did not work until I tried several times turning it on and off. It then worked once but then did not. It worked once more after several tries. I then called a repairman suspecting the control board. He confirmed this and tested the old element which was in good working order after all. A new board has been ordered.

I tried to unplug old element without success. Called appliance repair man and he pulled part way out, took hold of place where plugged in with pliers and unplugged. While holding back part of plug he plugged in new element--$60.00 later.

The whole job took about 20 min. TURN POWER OFF AT CIRCUIT BREAKER!! Remove 4 screws from the convection cover, then 2 more holding in the broiler element, disconnect 2 wires, and connect to the new one. put the screws back in, the cover back on the convection element and you are done!

Slide oven door off slides and put oven door on table. Removed 2 torx-20 screws from top of oven door on the inside. Remove 4 sheet medal screws from the bottom of door 1/4' socket heads. The inside of the door will now separate from the front of door.Now you can see 2 screws on each side of the door handle end caps on 1/4 " socket heads. Remove the 2 screws on which ever side is broken and remove old end cap and side new one on an install 2 screw. When you put door back together there are 2 spring steel spacers that fall off the top 2 screws that hold the inside and outside at the proper space! Parts Select service is EXCELLENT!!!!!

unscrewed broken end cap, removed from handle and replaced the new end cap

Turn off breaker to oven from electrical panel, locatge all screws and remove. Use caution when removing element from clips if not replacing the clips. When removing the element, be careful not to damage connecting wires as they do not pull out very far. Be sure to reattach correctly. When replacing the oven seal, be careful not to disconnect the wires to either element as you slide the oven compartment forward after removing screws. It can be difficult to find the wires behind the oven compartment if they disconnect.

First, the order was shipped and delivered immediately. The model number had a wider range to select from and I had to guess which was the better fit. Other then that the new handle installation was a snap. Thank you and we would surely order from your company again.

ordered part came in noticed i had to make ajustments to new heating element took socket set and unscrewed four screws put a retainer on the wires that came out of the wall to make sure they didn't go back into the wall and would be unretrieveable. installed new screws and cover plate and turned on the oven all done works perfectly.

Just like the other responses described with two additional steps: 1) with a convection oven you have to remove the fan cover. It has four screws, the same size as the broiler element screws....but, get a piece of stiff cardboard the same width as the oven; put it all the way back, under the fan cover. There are holes in the oven bottom and your screws really want to roll into those holes and disappear; the cardboard will cover the holes. 2) as soon as you disconnect the element from the electrical wires....put a twist tie or other clamp on each wire as they want to fall back in behind the oven and you'll end up having to remove the build oven to get at the wires. The twist tie should keep them from falling out of reach.

Make sure the oven is turned off. Simply remove the metal cover over the convection fan. Remove the two (2) oven element screws holding it to the oven wall. Disconnect the two wire leads. Connect the new element to the leads and reverse process to attach the new element to oven back wall and install the convection fan cover.

remove and replace

took the old ones out and put the new ones in their slots. No issues

It was easy as pie. Just followed the instructions.

Bake element was glowing. . . Then by the morning, a "cancer-like" thingy traveled the length of it!after kicking off the breaker, I brought the broil down to the bake>. It worked (not recomended>. . But it worked for me). Came the new element, in 2 days. . . And all is back (the broil slots didn't line up so it was a redneck install at best til I got it back to normal). They should add the owner's faces to mt rushmore! Bless you all!

When i finally got the right part.It only took few minutes to screw in and it worked perfectly.Customer support was very helpful in finding the correct part.thanks