JCKS05GS-1 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- frederick from kingwood, TX
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Element burnt through
Repair was very easy-make sure you shut the electricity off at the breaker box-having the oven control off does not kill the electricty to the element . Removed the screws, pull out the element, disconnected two wires, re-attach to the new element, install the screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lori from Fairfax, VA
- Parts Used:
- WB7X7183
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Wrench (Adjustable)
Door Handle End Cap Broke Off
Dislodged screws to oven door to get to handle assembly. Fairly easy, however, new door handle end caps do not come with screws and the old screws were not a good fit. Almost stripped the old screw trying to get it in place. Strongly suggest that Part Select send replacement screws with handle to facilitate repair. Door handle is back up but is now loose until I can find/secure appropriate replacement screws and repeat the process all over again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Arvada, CO
- Parts Used:
- WB44K5013
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Heating element in bottom oven burned out
First I made sure I turned off the breakers in the circuit box that controlled the circuits for the ovens . Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. The factory wrapped a large amount of tape around the connection between the wires and the heating element. That took a while to get off. And I searched for heat-resistant electric tape to replace it (because, it must have served some purpose if they had it on originally). The wires hooked onto the spade connectors for the new elements with no problem. I pushed them back into the hole in the back of the oven, replaced the screws, turned the breakers back on, and it worked great from there on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Southlake, TX
- Parts Used:
- WB7X7183
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench set
End caps very difficult to get on the handle bar
This the second time in three years the end caps broke. The first time the replacement end caps slid right on but, this time it was an extreemly tight fit. I had to sprsy white greese on the handle bar and inside the end cap and, even then I thought the end caps would break it was so hard to get on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HAROLD from LODI, CA
- Parts Used:
- WB7X7183
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Broke ed cap on oven door
Repair was basically simple. Remove 6 screws holding door facing on door, remove one screw holding handle end caps in place. Then reverse the operation installing handle end caps. The problem I had was that the new a end caps had different dimensions than the old ones and the handle wouldn't slip into them. Had to carve away material inside the new caps with an exacto knife in order to fit the handle. The result was a 15 minute job took well over an hour
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Roanoke, VA
- Parts Used:
- WB7X7183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
End cap broke to the oven door
I took the old cap off, and replaced it with the new one. I am glad I had the sense to buy this online, If I had gotten a repairman to fix this, it probably would have costs $100.00 instead of the $17.00 it cost me to fix it myself. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marsha from Charlotte, NC
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
broken element
turn of electric oven, removed screws and took out old element and put in new element and replaced screws. done simple and easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugene from San Rafael, CA
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Oven Element melted
Turned off power. Removed two screws. Took out old element. Used pliers to remove connectors. Installed new element. Set screws. Turned on power. Works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Toni Ann from Manalapan, NJ
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The baking element broke.
Ordering and shipment of the part were quick and easy. The price was excellent too. It was the easiest repair we ever had to do to an appliance. After removing the screws that held the element in place and disconnected the part, my husband immediately connected the new part. It took less than 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rodolfo from Waterford, MI
- Parts Used:
- WB7X7183
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Door Handle bracket was broken
Unscrewed the broken door handle from the range with torqx bit, and replaced, hardest part was getting the plastic handle on the black pull bar. you may want to use a mallet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clifford from parkland, FL
- Parts Used:
- WB7X7183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Both Door Handle End Caps broke
It took longer to go and buy the star tool then the repair. If you have the tools close it is a ten minute repair....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynne from Coto de Caza, CA
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Baking Element wouldn't heat but the broiler worked fine.
First I turned off the power at the fuse box, then removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and replaced with the new element. Very Easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KY from Lenapah, OK
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Oven would not heat
Turned off power to oven. Removed two screws that hold the element in place. I then pulled out the element far enough to get to the wires so I could disconnect them. I connected the new element and screwed it back in. 10 mins tops!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alexis from Birch Run, MI
- Parts Used:
- WB3X5699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
timer and cleaning timer knobs broken
two of the knobs pushed on perfectly,
Other than that they came quickly and I loved the service.
Thank you
Other than that they came quickly and I loved the service.
Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Colville, WA
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
element burned out
removed and replaced
Was this instruction helpful to you?
Thank you for voting!