JMP28BC1AD General Electric Range - Instructions

I unhooked the main power cord, unhooked the worn out block terminal cut the tape that was holding all the wires together. Removed the back panel and followed the wires unhooked the 2 wires and installed the new block terminal. Tied all the wires back, attached the back panel and plugged the power cord back into the outlet. i tested the burner to see if it was working. The burner is working great, instructions were easy to follow and my wife is happy. Thank you

Was very difficult to be certain of the right controller due to the exact model number of the range did not exist. Somewhat of an expensive part to make a guess.
After contacting no less than 5 parts dealers, Part Select was the only company that could immediately identify the correct number, (the model # on the range had an extra zero in the middle).
Was able to purchase the part confident it was correct, at a good price, with fast shipping.
Thanks

unplug it and plug the new one in

remove broken heating element and install the new one

Absolutely no tools required for this task. Simply align the prongs to the female portion on the stove top. Carefully push in until the element is in place then line up with the drip pan slot. No instructions are necessary!!

standard procedure, very simple

I UNPLUGGED THE WIRE, ASSEMBLE THE BURNER ELEMENT KITS
LIFTED UP THE SURFACE BURNER PANEL,
OPENED THE BACK RANGE COVER,
UNSCREW THE NUT HOLDING THE BURNER CONNECTOR, DISCONNECT THE REPLACEMENT WIRES ON THE BACK PANEL
TRACE THE NEW WIRES CLIPS TO THE BACK PANEL & TIGHTEN THEM WITH EXISTING NUTS
SCREW THE OTHER ENDS BACK WITH NUT HOLDING THE BURNER CONNECTOR

After watching the video and ordering the parts and searching for the right size socket (which took most of the time) and finding medical tape as I had no electrical tape I took of the back unhooked the terminals and following the wires to determine which ones needed to be replaced I followed the video instructions on reverse as my son had spliced new terminal blocks into the old wires I taped each new wire to the one it was replacing and pulled it through the back of the stove and into the front attached the new wires to the new block and pushed the clips on the other end of the wires to the knob boxes. I rolled up the excess wire and taped it securely with medical tape so it wouldn't unravel and be in the way when I reattached the back shield on the stove. After I repeated the process for the second terminal (I had two that kept shorting out) I reassembled the stove plugged it back into the wall and used both burners that night to cook dinner! I have had no problems with those burners since then. Really if you watch the video first and follow the instructions you should have no problems. It is really quite simple if someone hasn't tried to repair the problems without replacing the wires. Splicing new blocks into old wires just doesn't work. If I have this problem again, which I hope I don't, I will be confident in my ability to fix the problem myself. Thank you parts select for repair video and the parts.

As with all of my orders from Part Select the part was as correct and arrived in a timely manner. The installation was easy. Remove two screws, unplug the old element from the wires, install wires on new element and reinstall the element. Restored power and everything worked fine.
Thanks,
Ken Fuelleman

I watched a video of a similar model to familiarize myself with the required steps needed. I opened the back and disconnected the power cord and ground wires connected to the removable socket I then removed the lightbulb and removable socket from the oven interior side. I then removed the defective light socket cup and replaced it with the part I purchased. After replacing the removable socket and lightbulb, the bracket holding the light cover functioned perfectly with the new light socket cup. Final steps were to reconnect the power and ground wires to the removable socket. I then replaced the back cover over the light socket cup area. One word of advise. Be very careful when removing and reconnecting the cables to the removable light socket.

Removed the old burner bowls, replacing them with the new ones.

I was very excited to get them in the mail but waited to install after a clean up but when I finally opened the box I found I only ordered 1 6 inch drip bowl. lol Now that I know they fit when I reorder I am ordering a who new set for later use.

pull out, push in

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Replaced the defective element with the new - all inless than fifteen minutes!

Did it By Hand
Your Shipment Time Excellant
Order it Mon. Received it Wed.


Thank You