JMP28BC1AD General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Becky from Piedmont, MO
- Parts Used:
- WB44K5009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
unit burnt out no broiler
took old unit and measured it part select made it easy for me ordered new unit and installed easily and quick thanks to quick service and shipping
Was this instruction helpful to you?
Thank you for voting!
Surface Burners were very slow.
Removed old surface burners and replaced them by plugging in the new surface burners. Now they work GREAT! Parts ordered and received with-in 3 business days. Fed EX delivered parts in good order very quickly. We recommend PartSelect.com
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marco from Santa Barbara, CA
- Parts Used:
- WB17T10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Two sockets for electric elements and their end terminals were badly burned.
0) Take the back cover of the range off.
1) Carefully noted how the wires and the sockets were connected.
2) Visually checked that the new parts were practically identical old ones.
3) Put together the new sockets from the parts in the kit.
4) disconnect the old sockets and put the new sockets in place.
5) For each unit disconnect one old wire at the time and connect the new wire. Repeat the same for second wire.
6) Neatly bunch together the rest of the wires with electrical tape. Do not cut the wires!
That's it! It took about 20-30 minutes.
1) Carefully noted how the wires and the sockets were connected.
2) Visually checked that the new parts were practically identical old ones.
3) Put together the new sockets from the parts in the kit.
4) disconnect the old sockets and put the new sockets in place.
5) For each unit disconnect one old wire at the time and connect the new wire. Repeat the same for second wire.
6) Neatly bunch together the rest of the wires with electrical tape. Do not cut the wires!
That's it! It took about 20-30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Isabel from The Colony, TX
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The burner bowls were burnt through and nasty looking.
I carefully removed the burners, removed the bowls and replaced them with the new ones. Easy as pie!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from Norwalk, CT
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replacement of old parts
Fortunately there was no repair needed, just a replacement of old parts, but I was very pleased with the speed of delivery and the quality of the parts. I'm a happy customer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Fraser, MI
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
In My Carelessness, I Ruined The Burners On My Stove Using A Really Abrasive Cleaner, And Had To Replace Them With New Ones. My Stove Looks Brand New, And I Feel Better!!
Nothing to it. Took off the old ones and put on the new! Tada - new stove!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Tucson, AZ
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Drip pans on stove top burned black
I got tired of trying to find the right parts in the stores and decided to order them. Finally I have the drip pans that fit my range!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Southern Pines, NC
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Surface element was corroded.
Removed existing surface element and replaced with new element.
P.S.
Part Select service was excellent.
P.S.
Part Select service was excellent.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rachele from OCEANSIDE, CA
- Parts Used:
- WB21X5301
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
F2 error code when oven was set at a higher temperature.
I pretty much followed the youtube video posted under the part that I needed. Turned off electricity to that area of the house. Unplugged stove. Took out the old sensor, pushed new sensor cord through the back hole. I did put a small amount of tape,so I could pull it through from the back better. It was impossible to get the clip disconnected in the back and the new clip didn't match up correctly anyway. Ended up having to cut the wires and strip them. I twisted them together and put on the ceramic wire nuts on. Reversed ever thing I did and F3 appeared. Looked that code up on internet. It was from an open or shorted oven. Suggested I check the connections. Pulled stove out again, unscrewed caps on wires and noticed the sensor's wire had another cloth type coating on it. I gentle cut that off, twisted and capped wires again. Plugged in oven, turn on electricity, and tried out stove. Everything is working just fine. Everything took a little longer because this was first time doing this type of repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- aiden from philadelphia, PA
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
drip pans had become old and burned out
Took off the ring burners and the old drip pans . installed the new drip pans and the old burners took less than 3 minutes...so easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from MASON, MI
- Parts Used:
- WB21X5301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Alarm would sound whenever oven turned on - with an error message code
Watched the video on the PartSelect site. Could not have been an easier repair and I saved the cost of a service call - probably saved at least $100 - $150 in service call and I can only guess what the labor cost would have been. Will use this business again for other appliance repairs on my older stove, washer, etc. By the way - the official Kenmore site said this part was no longer made and unavailable --- Thank you PartSelect for having the part and saving me the cost of buying a new stove!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lance from HAHIRA, GA
- Parts Used:
- WB17T10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Terminal block connectors worn out wasn’t making a good connection with the stove top burner
Cut 4 inch’s off the new terminal block wires then using my wire strippers stripped 1/2 inch off the ends , the old terminal block wires I stripped 1/2 inch at the ends using a wire nuts on both wires and electrical tape connected the terminal block to the stove plugged the new burner in and the burner worked 100%.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emma from The VIllags, FL
- Parts Used:
- WB30M1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old unit failing to heat all coils
I first removed the unit by pulling gently from connection. Replaced the new one in that same manner - simply inserting into connection.
Very easy, I'll probably try it again soon.
Very easy, I'll probably try it again soon.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from PLANO, TX
- Parts Used:
- WB44K5009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Socket set
The top (broiler) element melted in two.
Be sure to flip the breaker to the oven to the OFF position before doing anything. Take out the two screws at the back of the oven that hold the element. Carefully pull the element forewarn to expose the connections to the wires. Disconnect the element from the wiring connectors. Be careful not to damage the connectors or the wiring. Plug the new element into the wiring connectors. Make sure you have the connections firmly in place. Push the wiring and connectors back into place. Replace the two screws. Make sure the element is resting in the spacers that keep it the correct distance from the top of the oven. Flip the breaker to the ON position, Turn the oven on Broil. The element should start turning a bright red. some fumes will come off the element. That is just oil from processing and handling. Your done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lan from SANTA CLARA, CA
- Parts Used:
- WB17T10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
It was burned out
I just follow Steve's Installation Vidio. My range works.
Thanks Steve
Thanks Steve
Was this instruction helpful to you?
Thank you for voting!