Models > JBP23 > Instructions

JBP23 General Electric Range - Instructions

Jump to:

All Instructions for the JBP23
61 - 75 of 177
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
William from Duvall, WA
Parts Used:
WB21X36771
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers
Burner only worked on High and very low temperature setting.
Your "virtual repairman" was fantastic. I would have purchased the wrong part without trhe diagnostic service. It said that 53% of the time the infinite switch was the problem. In my case it was 100%. Why I put up with this problem for 6 years I will never know.

Repair job was easy but longer than the 15 minutes that it said it would take.
2 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Grant from Mims, FL
Parts Used:
WB3X5699
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
broken knobs
every thing went just fine. A simple job at best.

What went better was the prompt service.

Thanks
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
selvon from MA, MA
Parts Used:
WB2X8228
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
burner inop
Received complete burner receptacle. Decided to take off stove back to plug in directly to burner control.
Turn on stove on low. No heat. Bad coil element. Checked for power at coil element. Switched another burner. It heated immediaetly. Have to order or find a burner element
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
andrew from langdon, ND
Parts Used:
WB21X36771
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers
Switch - and the connection wire to the burner
First of all I did this repair because the wire to the burner shorted out. I did the wire portion first - only then did I know I needed the switch kit. (The burner was operating while my old swithch was OFF). The first (wire replacement) repair took about 10 minutes - I followed the guidance on this web-site. The second repair (The switch) took about 20 minutes. The switch ws not the same as the original. Just be careful to mark each wire as you remove them from the old switch's posts. The posts on the switch are marked and you need to place them on the like-marked corresponding posts on the new switch. All is well, my burner is operational.
2 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Darrell from Cape Coral, FL
Parts Used:
WB31T10014
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Obsolete appliance parts missing
Thank goodness for PartSelect.com
When we moved into our home the microwave and electric range are obsolete appliances and were missing parts. PartSelect.com has pictures of parts on one inch grid pattern so I was able to select the hard to find parts that would fit perfectly and they did.
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Whendy from Hampton, NY
Parts Used:
WB31T10015, WB31T10014, WB30M2
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
my burner burned out and burnt the buner bowl
I just pulled out the old element and put the new one in and replaced all of the burner bowls .these are the only ones I found that fit my stove
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lois from Sarver, PA
Parts Used:
WB30M1
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Plug-in surface element was covered with a melted on forever microwave plate
Just put it right into the receptacle. I want to add...we had gone to our local appliance store and brought home a wrong-size unit. Got online and your website came up. It was easy to find the correct part, ordered it and it arrived 3 days later. I have already recommended your website to 2 of my friends. One very good experience!!!
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
MARLENE from EUGENE, OR
Parts Used:
WB30M1
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
element broken at contact point
ordered new surface element and pushed in to conector turned on switch to test and works fine thanks
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Harold from Gloversville, NY
Parts Used:
WB30M1
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
burned-out six inch electric stove- top burner
Removed the old and slipped in the new.No problem and it works fine.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
LISA from GLENDALE, CA
Parts Used:
WB30M2
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Electric stove 8" burner needed to be replaced
Installation took 30 seconds. Your website was easy to use & the part received was just as described. It arrived beautifully wrapped & in just a few days. ABSOLUTELY AWESOME!I will recommend your site to everyone.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Carolee from Carson City, NV
Parts Used:
WB31T10015, WB31T10014
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Change out burner bowls
Took out the old ones and replaced with the new ones. Very simple task. It didn't take 5 minutes.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Shawn from Lubbock, TX
Parts Used:
WB31T10015, WB31T10014
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Replace Drip Pans on Stove Top
Just removed the old drip pans and then inserted new ones...pretty dog gone easy!
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jeannette from Haskell, NJ
Parts Used:
WB30M2
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Burner heating coil element would not get hot.
I pulled out the heating coil and pushed in the new coil. I turned the stove top on and heard a sound like "dzzzt". I immediately turned off the burner and waited for it to cool, then pulled it out. The part had a burn melt on one side of the end prong. It turns out that the part that the burner plugs into needs to be replaced. Actually, the stove top is over 20 years old and my landlord will have to replace the whole unit. So it turns out that I didn't need to order a surface element after all, but it was very easy to install!
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Scott from Dallas, GA
Parts Used:
WB30M2
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Burner not working.
I pulled the old burner out and slid the new one in it's place. Turned on the eye to make sure it worked. Felt heat in a few seconds and turned off.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
DEBRA from DULUTH, MN
Parts Used:
WB30M2
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
I Ruined My Burner -- This Was A Solution For Me...
I simply pushed the new burner into hardware. I then tested it to see if it works. . .
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JBP23
61 - 75 of 177