RA720KC General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- GAIL from STREAMWOOD, IL
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed new drip pans
Not really a repair. But would like to say, I like the price and shipping was super fast. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sunny from Salt Lake City, UT
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
stained drip bowls
unplugged burners replaced drip bowls plugged in burners
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from Lynn, MA
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Connector to burner is out.
Remove old wire and replace new wire into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Felipe from Donna, TX
- Parts Used:
- WB24T10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The burner combusted burning the the burner switch
Disconnected the appliacnce from the power source. Using screwdriver, removed the back panel and disconnected every wire that are connected to the switch. Pulled out the front nob and removed the switch. Then install the new switch by screwing it back in. Place all wires back and back panel. Connect and finish.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Constance L from Woodhull, NY
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Disgusting looking burner drip bowls.
Just had to change out the drip bowls, easy. But, I wanted to comment on the quick delivery on the new bowls. I was impressed. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leslie N from Carson City, NV
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
none
Took the old pans out and put the new ones in. Simple as pie
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Jericho, VT
- Parts Used:
- WB24T10025
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Burner was always on high when on.
Disconnected the power. Removed hex head screws from top and lower rear panel. I think there were 8 all together. Pull the knob of the burner control, removed two screws that held the switch in place. Moved the wires one at a time to the new switch, re-assembled. Burner worked properly. Very easy to find the right part from this web-site, and the instructions from others like this were helpful. Easy fix!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curt from Maple Grove, MN
- Parts Used:
- WB24T10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Burner light would not shut off
Checked each burner switch by disconnecting the light indicator wire. Located the switch, replaced the switch and the indicator light operated as it should.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from N. Fort Myers, FL
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed "original style" on older stove
I needed to replace all stovetop bowls and found all after-market bowls "just a little off" effecting how flat the burner rested so called PartSelect's hotline and was assured that if I were using the actual model number found on the stove the parts would definitely fit and not almost fit, guaranteed, and they did!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Moses from Spring Valley, NY
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the burner did not get hot
First I shut off the breakers. I cut the wire from the end of the new part and took off the plastic off because the end of the new wire has a special end clamp to connect to the old wire which is in the stove but that wire didn't have the same clamp to be able to connect them together therefore I needed to cut the wire to from the new part also and connect it to the old wire with a wire nut which is on the range which is attached to all the other burners. Twisted them together and I put a wire nut to hold them strong together, pushed in the end of the burner into the 2 holes of this new part. I turned on the breakers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Renton, WA
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Found out Drip Bowls can not be added to self-clean
Dropped in new bowls. I was surprised how in-expensive new ones were.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from limerick, PA
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken surface burner terminal block[recepticle]
as described on video,with no problems,very helpful
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Woodbridge, VA
- Parts Used:
- WB25T10041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Orange light "Hot Stovetop" lense broke off.
Parts arrived in record time and the right parts. The detailed diagram was so helpful in finding exactly the part I needed to order. Was so easy my girlfriend with no mechanical or electrical experience completely helped me through the entire project. She secured the electrical breaker to the range, and I had the top back to the oven removed. I showed her how the little white box simply slides off the lens cover, then replaced the new one in the holes and slide it back on. Secured the back and she turned on the breaker back on...and all lights work. Thanks for making this project easy, simple and quick.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Godfrey from Virginia Beach, VA
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Does not. The heating element sucket is crack and burn loss connection.
Replace the sucket for the heating element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Mead, CO
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replaced my drip pans
The new drip pans are great. I had purchased generic ones locally that were supposed to be universal. The problem was that they did not fit right and the burner coils did not sit flat. The new drip pans fit well and look great too.
Was this instruction helpful to you?
Thank you for voting!