JMP263D1 General Electric Range - Instructions

First I located the circut breaker to the oven- once no power supply was confirmed (oven light was out) I diconnected the screws that held the old element in place. Pulled the old element forward and disconnected them from the wires. The hardest part was getting onto the oven to reconnect the wires to the new element since the door opens down the work space is a little tight and awkward. Connected new element and replaced screws. Done in less than 20 minutes and no repair service calls to pay!

Bake element was getting old, thin and burning hotter in various spots. Ordered new part. Upon arrival, turned off power in the fuse box, 2 screws removed the old bake element from wall of oven. 2 more screws disconnected the power supply. Installed new part, reconnected all 4 screws and turned power back on. Entire job took 15-30 minutes, extremely easy.

Turned off power to oven and removed screws attaching element to back of oven with a socket wrench. After removing the screws, I pulled element out about six inches and used a screw driver to remove the screws that attached the two electrical wires to the end prongs of the element. After removing old element, I simply reversed the process to install the new element.

First of all I would like to praise PartSelect.
I ordered the part Friday afternoon and it was delivered the next day (Saturday) I couldn't believe it, because I chose the cheapest shipping, probably had something to do with it coming from in state.
First MAKE SURE BREAKER IS OFF, unscrew the old element from the inside of the oven and pulled it out and then unscrew the connection piece,(make sure wires don't fall back through hole once disconnected) re-screwed the new element to the connection pushed it back through the hole and then re-screwed the mount to the inside of the oven. It was that simple by far the easiest home repair I have ever done and I'm a 52 year old women.
Praying before always helps too.

The very first thing we did was turned the circuit breaker off and unplugged the range.
My husband removed the back panel and unplugged the switch. Drew a diaghram of the color coded wires. When we received the new one he broke the extension bar off to fit the knob, plugged it in and we were back in business. It was very easy for my husband as he is a mechanic (millwright). However, if you are mechanically inclined it is an easy fix.

Pulled range out from the wall. Unplugged cord from outlet. Removed old knob, removed two phillips screws a very top of chrome trim, removed six nut-head screws from back to reveal the switches...removed two set screws from the front at knob base. Visually checked to make sure wiring post of new switch matched the old one. There was enough slack in the wiring to remove one wire at a time and connect it to the new switch in its appropriate place. Put new switch in the panel and secured with the two set screws. Select the bushing that would take up the slack for the old knob to fit on the new switch stem. Held new stem at its base with pliers and used another pair of pliers to snap the stem at appropriate length. (The new stem could not be broken off short enough to have the knob as flush to the panel as the other knobs...this was the only negative factor in the repair) Replaced nut-head screws and phillips screws. I was especially pleased with the quick delivery of the part...even without special shipping rates I received the part in less than 18 hours from the time I ordered it online!

I removed the two screws that held the element in place. I pulled out the element and disconnected the two wires and unscrewed the screws and then place the new element to it. screwed the wires back to the element wires and then push it back in. Replaced the outside plate and screw the two screws back in.

Save myself money by doing it myself.

First I made sure the electricity was off. Then, I flipped the burner up, and loosened the screwon the hinge. This allowed the burner to extend onto the cook surface. After loosening the clips holding the ceramic insulator together, the wires to the element were exposed. The wires were then transferred to the new burner element from their corresponding position on the old one. The new ceramic insulator was affixed over the wire with clips, and the hinge reattached. The chrome ring was worked over the burner, and the burner reseated in its proper cook poistion. Testing confirmed the burner to now work as new.

First I removed the two srews that hold the element in place. I then pulled the element out about three inches and disconnected the two wires. I attached the wires to the new element and we had our oven working again. I really am happy with the timely service I received from PartSelect and would recommend them to anyone.

1. Turn off power to range and remove element.
2. Remove clips from ceramic guards.
3. Disconnect wiring.
4. Connect wires to new element.
5. Install ceramic guards and clips
6. Attached element to range.
7. Restore power.

removed the end caps from the stove panel, unscrewed the back, unscrewed the old switch, CAREFULLY noting which wire went to which terminal, removed the wires.
Reversed the process. took a little longer because I felt compelled to do a thorough cleaning while I was there.

Glued the timer knob on (shaft was broken and a bit short). Took back panel cover off the range and snapped the old pilot light out and snapped the new one in.

Unplugged Stove, pulled away from wall. With smaller wrenches, took the two screw-nuts off the inside back and above that hold the broiler element in place. Since it is an older stove...took the back panel off the stove with philips screw-driver which consisted of 10 screws. Once that was removed was able to unscrew the broiler element from the two wires that provide the electricity. Used the flash light when I had to unfasten the screw-nuts inside the stove because kitchen lighting wasn't strong enough.

Easy

turn off breaker in electrical panel....remove stove socket from outlet....remove rear panel from stove....undo wire connectios from broiler element....inside the oven, gently move thermostat wire out of the way....unbolt broiler plate from rear wall....remove broiler hanger and then broiler element....reverse procedure and you're all set.