J33201 General Electric Range - Instructions

The stove was new when we moved into our new home but opted to leave "our" stove in the basement until the one that came with the house had seen it's better days. The removal of the original element required the use an allen type of driver - it's removal was simple and the new element popped-into place without a problem and I refastened with the screws that came with the new element. The part arrived from PartSelect right on time, in good condition, and I would definitely do business with PartSelect again when I need to! My only complaint has nothing to do with PartSelect, it is the angle one must assume to refasten the part into place! Thank you, and I'll be back!

removed old element rewired new element,turned back on power

Removed old, burned out element, and replaced with a new element. The worst part of the entire job was getting the oven door assembled back on to the oven.

First my husband removed the screws that held the element in place, pulled it partially out and then disconneted the wires. He located the part number that was stampted on the defective element and then I searched the internet for GE parts. I noted the price at GE site and continuted to search. The PartSelect price was about 1/2 of the GE price. We ordered the part, it arrived in two days, and we replaced it in less than 30 minutes. We were very pleased.

Just re-connected the electrical. Was the exact/correct replacement part. Repair successful. Thanks.

The old eye was lifted up, hinge screw removed, and three screws removed from the eye that connected lines to it. Did just opposite for installation. Very easy. The hardest problem was finding an eye with three screw-type connections.

Some times it's not the element at all, as in this case. After rmoving the element I found the wires broke. Fortunatly I had some high temp wire left over from a earlier oven repair. I used butt splices and heat shrink tubing to repair the wires. Then I crimped on a couple of eyelets and fastened things dow.n I received a big kiss form the wife for getting the broiler fixed so fast. Maybe a little extra work, but the rewards were worth it.

Unscrew 4 easy nuts and 1 most difficult nut, gently pull both long and short wires, at this point assure the wife that you did turn off the power.You may wish to attach a cord to short wire as it wants to vanish into the rear bowels of the oven On instruction of the wife clean the oven. Reverse dismantling procedure. Switch oven on. Bask in wives praise.

Range is 45 yrs old. New drip pans are different shape. This is only place which had them and VERY GOOD price. Delivery was quick, too!

I unscrewed the screw that held the element in place and then took the hex head nuts holding the 3 wires off the old element. When taking the wires off, I had the new element next the old and put each on the same connection one at a time to make sure I replaced the wires in the same location they were on the old element. After connecting the 3 wires, I reattached the element to the range.

The repair was very eash. The replacement element fit perfectly and only involved removing two screws, pulling the old element out far enought from the bak of the oven to disconnect the wires held by two screws . Disconnecting the two wires and installing the new element. This is a 25 year old appliance and is back to working like new. One note, be sure to shut the power off to the range because one of the wires connected to the element remains HOT! even if the oven is not on.

The repair went well and once again my stove that was installed back in 1968 is working perfectly. We will be buying another 6" burner and 2-8" so we have them when they begin to burn out. We looked everywhere for a replacement and was told they do not make them anymore, but we found it here. Thank you!

I purchased a set of drip pans at the store only to find out that they were not for GE Ranges. I got on line and inquired and your representative was very helpful. The repair was easy. After cleaning the stove I removed the old drip pans and installed them one by one. No problem!

I tried first to replace them, with a set I bought at a local hardware store. But they were too small. So I went on the internet, and found Part Select, and thanks to a very helpful guy, who made the extra effort to find the exact drip bowls, I now have a nice, shiny stove-top again. Installing them took two minutes... tilt the burners up, and slide them in. No problem.

From inside the oven after turning off the breaker I removed all of the mounting screws with a nutdriver, I removed the wire screws after taping all of the wires together with a small piece of tape to prevent them from falling back into the opening. I installed the wires with the original screws as the provided screws would not fit the holes, tightened them, removed the tape and placed the element back into the opening. I then tightened the hanging brackets, after getting them to align and then tightened the rear mounting bracket. It did help to adjust the baking rack down and leave the baking rack in place to have a place to rest my arms. The install then became a piece of cake!