J33201 General Electric Range - Instructions

Old gasket had become brittle. Was able to find the 22 yr old model and part on PartSelect (could not track it down on GE's site. Inner panel was removed with four screws. Old gasket came out. Installed new gasket making sure the bead fit into the groove provided in the door panel. Re-assembled. All is well. Thanks

The hardest thing was finding the part to order! The GE Cooktop is from 1957 when the house was built. I followed the instructions that came with it. After seeing where the screw on hinge was supposed to be, I cleaned away the caked grease and finally saw the screw. I had to use a nut driver to remove it since it didn't have a slot for a screwdriver. Once that screw was out, the rest was easy. Before disconnecting any wires, I laid the new and old parts beside each other and drew a diagram showing where each wire (red, black & white) connected. It was a bit scary stripping the wires since they were old and fragile. It said to bend them into a "U" and solder but I didn't have soldering skill or equipment so I just tightened the screws holding the wires carefully. The connections are all nicely isolated in the bakelite insulator so it didn't seem cruicial. After working the new unit into place and turning on the power (at the circuit breaker), the burner worked perfectly. The replacement part looked exactly like the original. I was so amazed to be able to obtain the replacement burner after all these years! Thank-you PartsSelect!

Successful repair to Our GE range, manufactured prior to 1965 (when installed in house). Pulled range from wall, unplugged, removed burned-out broiler element. Previous check with GE to make cross reference of range part number to Part-select part number for this nearly 50-year-old range. Obtained new part and installed. Works. Range has self-cleaning oven, accidentally destroyed thermal switch attached to element mounting bracket, difficulty with frozen mounting nut. Self-cleaning still works; thermal switch locks out a solenoid which defeats door latch; prevents premature opening of oven door when oven too hot to open safely. Internet search did not find GE part but there are generic devices of the same type available; will consider installation later.

After ordering the proper part with the help of the phone customer service tech, I moved the stove from the wall, unclipped the connector, removed the two screws holding the sensor in place, and removed it. Reversed the above to put it back, and the oven holds perfect temperature.

It was so easy. I turned off the power to the range, loosened the hinge screw and removed the burner unit from the stovetop. Next I removed the two spring clips holding the ceramic housing covering the three connectors. Then I loosened the three screws holding the 3 wire connectors to the burner, reconnected the 3 wires to the new burner unit, positioned the ceramic insulator housing and reinstalled the spring clips and finally replaced and tightened the hinge screw. It took about 5 or six minutes, max.
You can do this!

Removed sensor from back wall of oven by removing 2 screws from flange. I could not pull the wire-nut connections out through the small hole and thought I would have to pull the whole oven out of the wall to acess the connections from the back so instead I clipped the wires close to the old sensor and connected the new sensor with the small wire nuts provided, then enlarged the hole in the oven wall, being careful not to pinch the wires then pushed the wire nuts and extra wire back through the hole and put the screws back in the flange.

First I removed the two screws in the back. then I removed the two screws attached to the brace at the top. pulled the old element out. Removed the screws that attatced the wires to the element. Attached the wires to the new element. Pushed the wires back in. Pushed the element in and attached the screws. Reattached the support. Turned on the broiler. The element smoked for a few seconds before getting red hot. It is working fine.

Pull the stove out from the wall and unplug. Had to remove back of stove, the aluminum sheilding and the duct work to get at wires use nut driver. Then used nut driver to remove nuts from broiler unit inside stove. Take the front overn dover off first. The new part did not match up with the wires so I used a needle nose to spread the wire clips just a tad so they would fit over the tabs of the broiler unit. Do all of this behind the stove as you do not have eough wire to do this effectively from the oven side. After I had the tabs fitted to the broiler unit. I removed them and fed wires back through the stove. I then went back to the front of the stove and put the broiler back in and put support bar back in to ceiling of stove and the two nuts back on to affix broiler to back of oven. Put the aluminum baccking and duct work back onto the back of the stove and plugged it back in. Pretty easy job.

Raise burner high enough to remove screw located on hinge between coils. Remove screw completely and lift-out burner and ceramic block with wire connections.
Remove the wires from the connector block and strip-back the ends of both about 3/4". Make connections per the diagram and then assemble the ceramic blocks around the connection in a sandwiched fashion and secure the halves with the clips provided.
Now sit the burner down into place. An extra pair of hands is good here to hold the chrome trim ring and the coil up directly opposite the hinge. Then, peek under the coil and using fingertips, get the screw provided started in the hinge bracket and run this screw up snugly. A 1/4" nut driver makes this part easier, but a screwdriver will get it done.
That's it. Just flip the breaker to restore power and cross your fingers. A fairly easy job that took about 40 minutes to do both 8" elements The potentially frustrating parts are the ceramic terminal block assembly and replacing the hinge screw, but a job that's very doable. Oh, don't forget to slip the drip pans back in.

Turned off power at panellboard. Disconnected mounting hardware from inside oven chamber. Pulled failed heating element with wires attached into the oven chamber. Disconnected wiring and reconnected them to the new heating element. Tightened screws while holding connectors with pliers. Applied electrical tape to connections. Pushed wires back into opening and secured heating element back into place. Restored power nad verifed proper operation. The other heater purchased will be used when the bake element finally fails,

(1) Turned off power source.
(2) Removed rust on screw heads before attempting to loosening them up.
(3) Pulled the element out to expose the connections.
(4) Disconnected with phillips screw driver, taped off wires to prevent mixed-up during re-installation.
(5) Re-installed new element using new screws provided.

Teh instillation was a simple matter of removing the old burners and replacing them with the new ones. Removal required the screw connector on each burner ring to be loosened and the reverse done when the new one was installed. The hardest part was finding the correct burners since the Model number of the stove was not in anyones file. This web site provided adequate pictures of the part to permit identification of the likely part to order. Thanks.

Simple repair that was complicated by not being able to remove the oven door, leaving a long reach to the element connections in the back of the oven. Other than the accessibility issue, the repair is easy. Remove two scews, pull the element out about 3 inches to access and unscrew the screws holding the wires to the element. Then reverse the process with the new element. But, because of the long reach, there were alot of dropped screws and cussing.

First removed oven door, according to Reader's Digest repair manual, then removed two screws holding element. Pulled element out several inches, then removed one side of bracket holding up front of element so that bad element could be pulled further out. Then disconnected two red wires from one side and two light blue wires from other side. Removed old Element. Attached two light blue wires to one side and two red wires to other pole, inserted element back into rear wall and attached with two screws, Re-attached bracket holding up front of element. Re-installed door. Tested and it worked fine.

Both the eight inch burner and the the six inch burner were not an exact fit. I used the old rings and the new burners. The eight inch burner fit well with the new drip bowl;however, the six inch burner did not fit with the six inch drip bowl and I had to grind off about an eigth inch from the diamiter of the drip bowl. I replaced most all the wiriing and after I get the lower oven element rebuilt it will be ready for a test drive ..can't wait!