PLES389DCC Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from HIGH POINT, NC
- Parts Used:
- 318255006
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Heating element broken
I followed the instructions from the lady taking my order she talked me through the steps
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rockie from KEIZER, OR
- Parts Used:
- 318255006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
burnt out element
Followed instructions on website. Went perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Misty from CUNNINGHAM, TN
- Parts Used:
- 318191023
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dual burner would only work on high and only the large burner worked
Replaced the dual infinite switch behind the panel. The wires were easily matched, even though the switch looked a little different. Works perfectly now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Landover, MD
- Parts Used:
- 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bilb went out
replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Oscar from Scranton, KS
- Parts Used:
- 316217002
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
F10 Error. Temp sensor at 1189 room temp ohms
1. Loosened 2 sensor mounting screws and removed them. 2. Tripped range circuit breaker to off. 3. Pulled out the range but left gas connected. 4. Loosened the 4 screws on RH side of the top back panel and carefully pried that side of the panel open. 5. Using fingers, threaded the sensor's wiring harness through insulation and into the oven. 6. Unplugged old probe. 7. plugged in new probe. 8. tugged wiring harness back through insulation behind the oven. 9. Using 2 screws removed in 1 above, mounted new sensor. 10. Repositioned top back panel and fastened it in place. 11. Shoved range back in. 12. Tripped range circuit breaker to on. 13. Reset clock. 14. Set oven to 450 for test tun. 15.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Houston, TX
- Parts Used:
- 318255006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Baking element not working
Bottom oven quit heating about 6 mos. ago and now top oven quit. Broiler worked fine on both. Bought 1 replacement element to try. Did not work on either oven. Found online where someone had found a bad solder joint on a relay board so I pulled the oven and removed the covers. (WITH POWER OFF. I made a diagram of the wire connections to the board and removed it. I FOUND a cold solder joint on the L2 connection of the top oven board. I found the exact same cold solder joint on the bottom oven board also. After resoldering the connections and touching up any suspect joints I replaced the boards. They BOTH WORKED fine!
Anyone that can't solder can take the boards to a local radio/TV repair shop and probably get the techincian to resolder it for a minimum fee. It is certainly worth the attempt.
Anyone that can't solder can take the boards to a local radio/TV repair shop and probably get the techincian to resolder it for a minimum fee. It is certainly worth the attempt.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gwyn from Boulder, CO
- Parts Used:
- 318255006
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The original element in the oven burned up one evening
We pulled the stove out from its slot in our island. We unplugged it and unhooked the gas line so we could get behind it easily. We then took off the back (using screwdriver) to get to the connectors for the element. We unhooked the connectors from the old element. Then we took off the plate inside the back of the oven (using screwdriver)and gently pulled the old element out. We seated the new element in the oven and then hooked it up in the back and put it all back together again. It worked perfectly! The hardest part was cleaning the dirty floor under where the oven had been for 7 years!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from olney, TX
- Parts Used:
- 318255006
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven wouldn't work
It's kind of embarrassing!
As the breaker was being thrown to turn the current off, I discovered that the breaker box was burn up at the breakers.
Short story but I got'er done! The problem now is there is something still wrong with teh oven!
I think I see a new one in the future!
Thank you very much for the very prompt delivery.
My purchase has been without a flaw.
I have already sent the part back for a refund.
It cost me something like $13 for this experience for freight.
I will remember you with my next need.
As the breaker was being thrown to turn the current off, I discovered that the breaker box was burn up at the breakers.
Short story but I got'er done! The problem now is there is something still wrong with teh oven!
I think I see a new one in the future!
Thank you very much for the very prompt delivery.
My purchase has been without a flaw.
I have already sent the part back for a refund.
It cost me something like $13 for this experience for freight.
I will remember you with my next need.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fritz R. from Carnelian Bay, CA
- Parts Used:
- 318041603
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
A friend shot out the front glass panel of my oven door with a BB gun!!
Just "locked" the hinges, pulled the door off. Removed the broken glass for the door. Switched the handle from the old door to the new one. thPut it back on e hinges.....viola!! new oven door glass!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Huntingtown, MD
- Parts Used:
- 903136-9010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bad control switch for burner
Turn power to range off at electrical panel. Loosened control panel exposing switch. remove old switch and replace. reassemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tony from Hartford, CT
- Parts Used:
- 5304409888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No Power to the Oven
Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue from Lampasas, TX
- Parts Used:
- 5304409888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Control will not work - only clock blinks
Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Foley, AL
- Parts Used:
- 5304524341, 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken globe in oven and burnt out light bulb
Easy as 1-2-3
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from Corona, CA
- Parts Used:
- 5304524341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lens cover for oven light broke.
Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Oro Valley, AZ
- Parts Used:
- 318255605
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
broiler element burned out
watched a U-Tube video on this subject.....worked like aa charm!!
Was this instruction helpful to you?
Thank you for voting!