PLES389DCC Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Frank from CHESTERTOWN, NY
- Parts Used:
- 318255605
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
top electric burner not working
2 screws disconnected old one and pulled out the new one in put in opposite way. The representative was so helpful, part came fast. thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from SAN MATEO, CA
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Repaired Oven Range Light Bulb
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Everette from HARRISBURG, PA
- Parts Used:
- 316217002
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Thermostat. Didn’t cut off at set temp
Phillips screwdriver used to remove 2 screws at top left in oven. Pulled thermostat out until I could get to the connector. Used pliers to hold wire, reconnected new plug , threaded it back into back of oven and reattached the two screws.
Saved $150 on a service repair call.
Saved $150 on a service repair call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from MOBILE, AL
- Parts Used:
- 316217002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
When oven was set at 400, actual temp would run about 285.
1 Turned off the oven breaker.
2. Removed the oven racks.
3. With a Phillips screwdriver, removed the mounting screws holding the temperature sensor and unplugged it.
4. New sensor plug did not match 20 year old connector. Had to cut and solder splice the connectors.
5. Installed the new sensor and now oven holds temperature steady.
Easy order, quick delivery and easy installation, happy wife.
2. Removed the oven racks.
3. With a Phillips screwdriver, removed the mounting screws holding the temperature sensor and unplugged it.
4. New sensor plug did not match 20 year old connector. Had to cut and solder splice the connectors.
5. Installed the new sensor and now oven holds temperature steady.
Easy order, quick delivery and easy installation, happy wife.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from FOREST HILLS, KY
- Parts Used:
- 316217002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven would start to heat then quit,checked the temperature sensor with ohm meter after cool down reading about 1100 ohms. I cleaned connection tried it again seemed to work well but quit again in just few days.
Pulled range out from cabinet, removed back plate, two screws inside oven attaching the temp sensor. Then pulled the sensor and wire through from back. Reverse to replace about Ten minutes
OEM parts plug in same, works great
OEM parts plug in same, works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phin from HARRISBURG, PA
- Parts Used:
- 316555800
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
The part I ordered has 5 connections and the part to be replaced has 7 connections. I had to ask a friend who is expert in electrical wiring to help.
My friend used a tester to determine where each wire was supposed to connect to. I'm not sure what he did with the extra connections.
Bottom line is this part should work but you need an expert to do it for you because it's, like I said, not exactly like the one to be replaced.
Bottom line is this part should work but you need an expert to do it for you because it's, like I said, not exactly like the one to be replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from WICKENBURG, AZ
- Parts Used:
- 5304409888
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
wrong part
my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as well as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from BELLEVUE, WA
- Parts Used:
- 316555800
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Element burned out
The original instructions were to replace burner and plug wires back in the same plug they came from.
The problem is that the plug order had changed between parts.
Use a pencil to highligt the plug numbers on both new and old plugset, to fint the new plug positions. And need to reorient one of the burners to allow existing wires to reach.
The problem is that the plug order had changed between parts.
Use a pencil to highligt the plug numbers on both new and old plugset, to fint the new plug positions. And need to reorient one of the burners to allow existing wires to reach.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael A from Fairhaven, MA
- Parts Used:
- 318041603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replcement of inner door glass which had shattered
Removed the door from the range, disassembled the door, removed all broken glass fragments, installed the new glass, reassembled the door and reinstalled the door into the range. Straightforward and easy. Keep track of which screws go where and it is a breeze.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christine from addison, PA
- Parts Used:
- 316217002
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven not reheating after initial heat up
unscrew the sensor inside the oven; took off the back of range to access harness of sensor; the replacement part harness did not match up to the original, so we stripped the clip from the end of the part and also the end of the harness in should clip into. after joining the wires together with ceramic wire nuts we tested the oven to make sure all worked AND IT DID!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from ROCHESTER, NY
- Parts Used:
- 318255006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bake element was cracked
Remove the lower bake element by removing the 2 retaining screws that secure the element to the inside oven back. Carefully slide the element out. There are 2 wires attached to the terminals of the element. While removing be careful to not pull the insulation out with the wiring. Attach the wires to the terminals of the new element and reinstall in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ryan from MORGANTON, NC
- Parts Used:
- 318198817
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Element not working
Open range door remove 2 screws on bottom of stove top remove top
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheila from Dayton, OH
- Parts Used:
- 318255006
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Bake element burned out in my slide in range
Turn off circuit breaker
Open oven remove two oven racks
Position flash light
Remove two Phillips head screws that hold the element in place
Gently slide out element until you locate the two small wires
Gently Detach the two small wires from the back of the burned out element
Position the new element in the bottom of the oven and attach the two small wires to the back of the new element
Gently slide the element back in place and replace the two Phillips screws that hold the element in place
Make certain the new element is lying flat on the bottom of the oven
Replace the two oven racks
Turn on the circuit breakers and test the oven
Open oven remove two oven racks
Position flash light
Remove two Phillips head screws that hold the element in place
Gently slide out element until you locate the two small wires
Gently Detach the two small wires from the back of the burned out element
Position the new element in the bottom of the oven and attach the two small wires to the back of the new element
Gently slide the element back in place and replace the two Phillips screws that hold the element in place
Make certain the new element is lying flat on the bottom of the oven
Replace the two oven racks
Turn on the circuit breakers and test the oven
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ashley from CARRIERE, MS
- Parts Used:
- 318255006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Bake element in our drop-in oven stopped working
We turned off the power, took out the element, installed new element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julia from NEW BADEN, IL
- Parts Used:
- 318255006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Oven Bake Element caught fire
Unplug the oven (very important). Unscrew the bad element and screw in the new one. Plug oven back in.
Was this instruction helpful to you?
Thank you for voting!