ACS3350AB0 Amana Range - Instructions

It took me a while to figure out how to access the igniter (I ended up removing the drawer and had to slide underneath the oven.) Once I removed the two sheet metal panels, I unplugged the old igniter and plugged in the new one. Installing the igniter inside the oven was easy--three sheet metal screws that hold the protective cover.

Baking ignitor glows but gas valve not opening. Replacing the bake ignitor solves the problem.

Here is how to do:
1) open the oven door, unload the racks, bottom plate, and flame deflector. unscrew three screws (phillips screw driver needed) to loosen the bake ignitor (along with the metal rack).
2) take out the bottom drawer. you should see two screw all the way at the back. unscrew them to take off a metal cover. you should see the connector. unplug to take off the defective ignitor.
3) plug in the ignitor and put everything back in reverse order.

It took me a while to figure out how to access the connector at the bottom back of the stove. The next time it should take less than 15 minutes.

1. Disconnect oven electric supply.
2. Remove oven door (2 screws).
3. Remove inside-oven bottom plate (slide forward, lift).
4. Remove inside-oven burner cover (1 nut).
5. Disconnect igniter enclosure (3 screws).
6. Remove under-oven drawer (slides out).
7. Remove panel at back of oven in under-oven compartment to access igniter electrical connection (2 screws).
8. Disconnect old igniter.
9. Extract old igniter from igniter enclosure. (Don't use much force; just slightly expand the metal flanges of the enclosure.)
10. Dispose of old (bad) igniter.
11. Insert new igniter into igniter enclosure.
12. Place igniter enclosure in oven compartment and slide electrical connector through to back/lower compartment.
13. Connect new igniter in under-oven compartment.
14. Replace panel at back of oven in under-oven compartment (2 screws).
15. Replace igniter enclosure (3 screws).
16. Replace inside-oven burner cover (1 nut).
17. Replace inside-oven lower plate.
18. Replace oven door (1 screws).
19. Reconnect electric supply.

remove oven flare pan in bottom of stove, about 25 screws, lift out and remove igniter. tip stove back and remove splash pan from underneath, 2 screws, unplug ignitor and reinstall using reverse procedure. igniter is very fragile so be extremely careful with it. reuse old hardware to hold in place,reassemble and good to go.

The repair actually started online trying to figure out the problem. The parts list and picture provided were a big help. I actually got lucky when I ordered the part. It was a little difficult to get to but once I got the old one out, it was easy and done quick. Saving at least $100 on a repair man was awesome. I had to find the part in the stove first. Then had to find the wiring harness to disconnect. After taking off the back panel and the oven burner plate, the wire harness was exposed. I disconnected, taped on the new wires, remounted the new igniter and put it all back together. Pretty quick and pretty easy.

First, i removed all of the oven parts that needed to come out in order for me to remove the ignitor. Second, removed the manifold and the old oven ignitor. Then, i checked for 120 volts going to the ignitor. Replaced the ignitor with the new one and reassembled all of my oven parts. 15 mins top, but of course it may take a little longer for those of you who are not elecrically and mechanically inclined. Very east to repair.

I first diagnosed the problem with an ammeter, after I was sure of the problem I ordered the part and it came in 1 day early. When the part arrived I removed 12 screws to access the old part, unplugged it, plugged in the new one. The easiest way to save $150.00 I've managed.

Shut off electric power. Removed bottom drawer.
Removed metal covers over burner in oven.
Removed 3 screws holding igniter in place. Disconnected wire plug under oven and pulled thru hole where igniter had been. Removed metal shield from defective igniter. Used care to place it on new igniter. Reinstalled everything.
My wife was observing and made me scrub under stove since I had the drawer removed.
I found the other repair stories very helpful in diaignosing my problem and ordering the right part. I ordered on Monday and received Wednesday afternoon normal delivery. Very good service.

First, I took out the racks from the oven. Next, I took out the black small square cover off the bottom of the stove, which gave me access to the oven ignitor. Then, I removed the screws to be able to take out the ignitor. Finally, I took the bottom drawer out to access the ignitor wire. I pulled the plastic connectors to disconnect the wire. I took the ignitor out and replaced with the new one. I put everything back in reverse order. The oven warmed up about 2 minutes after I turned it on.

Pulled the burner cover, removed two screws holding igniter in place, pulled oven out from wall and unplugged igniter at back, feed wire and plug back thru to oven. Removed old igniter from holder slid new one in place and reversed procedure to feed wires back thru to back side. Plugged in igniter replaced burner cover and pushed stove back into place. The procedure took about five minutes if that.

Thanks to previous reviews it was really easy! Popped cover plate off bottom of oven. Removed diffuser plate by using socket wrench to remove one bolt. Removed three screws (one on top; two on left side) of bracket. Good idea to use a magnetic screwdriver so they don't get lost! Slid igniter out of bracket- a bit tricky but gently eased it out. Slid new igniter in place taking care not to touch the element. Dropped wires and harness down next to old ones. Removed bottom drawer, crawled under and switched connections. Put everything back together. It did take a little longer for the new igniter to start the first time- about one minute- but now fires right up.

Part arrive only a couple of days after ordering, and installation time was less than to schedule a repairman! My only regret is that I didn't send my better half off for the entire afternoon so I could really make it out to be a big deal as my brother-in-law, the appliance repairman, made it out to be!

1.) Trun Off Power
2.) Remove the Storage Drawer and the two (2) screws holding on the (Ignitor Plug) access cover-plate located in the back of the storage drawer access. (see page 15 if same model)
3.) Dissconnect the Ignitor Plug
4.) From the oven opening remove the three screws holding the Ignitor Holder.
5.) Remove the Ignitor and Holder from the oven by gently guiding the wires through the access hole
6.) Pull the Ignitor from the holder
7.) All Ignitors are extremelt fragile; install the new Ignitor into the Holder and make certain it is installed tight, mine was not. (Slight bending with my thumbs on the 1/4" flanges might hold it tighter if it is lose.)
8.)Reverse the process.
Note: One person here said they removed "ALL" the screws, maybe it was a different model, I only had to remove a total of "5" screws, two at the access cover plate and three at the Ignitor holder.
First time took me 20 minutes, if I needed to do it today, maybe 10.
Please also note that I didn't troubleshoot the Ignitor, as I didn't have a wrap-around amp meter, but the typical problem here would be the Ignitor, not the Gas Valve. Good Luck, pt

basicly just replaced the element by unplugging the connector and removing the three screw that hold the element. easy process.

I identified the igniter problem in the lower part of the oven by turning the upper broiler on and finding that it worked. I then knew it was not a gas supply problem. Replacing the igniter required removing the two oven racks, removing the drip pan, removing two screws that connect the igniter to its mount and disconnecting the wires in the back of the oven. The install was the reverse of removal. One tip, on my oven I was able to lift the oven door off of its hinges which allowed much easier access to the igniter.

Ordered new ignitor and recieved it in two days. Took out broiler drawer, took out 6 screws ,replaced ignitor reinstalled screws and broiler drawer in less then 15 minutes. New ignitor works perfectly. Couldn't of been any easier.