ACS3350AB0 Amana Range - Instructions

shut off gas at tank, pulled stove out from counter area to gain acess to back, removed oven door removed removed screws holding igniter unit in place, i then removed the stove rear panel to get at the wiring for ignitor,remoded old part returned to front and installed new part, checked voltage then re-connected new wires, turded gas back on and tested oven, oven came on less than a minute, put rear panel on stove put door back on and put stove back into counter area, stove works like new.

Researched through this site to find part numbers and names. Youtubed it to see how to install the part. Ordered the exact part via this site and received it in only a day or two. Installed it in less than 15 minutes and the oven works amazing. It gets up to temp quickly and holds temp better than it has in years. Very satisfied!

First turned off power to oven, Took burner out by lifting up and pulling out, then pulled out wires attached to the oven and igniter, removed two wire nuts and disconnected the wires then removed burner assembly from oven. With screwdriver and nut driver removed old igniter from housing and put new one in place, tightened up screws carried back to oven reattached wires with wirenuts and feed wires back into oven, then put burner back carefully silding igniter into hole in back of oven. Turned power back on to oven and worked nice. Took all of 15 mins to complete.

I just replaced the racks with beautiful, new, shiny racks. My wife was very pleased

After I received the new hinge in the mail, my 13 year old son volunteered, for a fee of five dollars, to put the new hinge on the oven door. Seeing "easy to install" on the outer wrapper of the new part, I thought I was being generous. However, my son soon let me know that the screws given with the new hinge did not fit into the predrilled holes of the oven. He tried and tried for over an hour to get those screws to fit. I decided to go to the home improvement store to buy bigger screws. I took the hinge with me and had the store employee assess the type of screws I would need. He then informed me that the screws were fine, but I needed the holes in the hinge to be drilled bigger. I bribed him by offering to buy him a drink if he'd do it for me as long as he was single. He laughed and drilled away. (Sometimes, single women, like me, get desperate!) He handed me the hinge with larger holes and I noticed the wedding ring. Oops...no drink for him!! But I did give him a great big thank you. Happily, I brought the fixed piece home and handed it to my son to continue with the repair. He tried again and this time announced the holes were drilled too big!! If there was a bridge nearby I seriously would have jumped! The next day I drove to my Dad's house...a true jack of all trades...and with his drill and two new screws, he said this should do it. For the third time, I handed the hinge to my son and VOILA!! It actually worked! Thanks Dad!! So much for "easy to install". Seriously, the incorrect screws were sent with this hinge! Anyway, I happily celebrated that night with a drink in my hand...minus the home improvement employee!

Took the pan out of the bottom of the oven. Took the screws out of the assembly for the iron, disconnect the power wires under the stove and pull out the old iron. Reverse the proceedure but be careful with the new iron, it is very fragile. Connect the wires put the screws back and you are done. Make sure before you start the job that you unplug the appliance !!!!

The repair was quite easy. Remove the two screws and put in the new part. The only problem I had was the hinge sent was the wrong side (but it still worked) and the new hinge had no threads for the screws. I had to tap the holes so that the screws could be used.

1. Remove sliding shelves and lower pan sheild
2. Remove flame deflector
3 . Remove the 3 screws that hold the igniter in place. Insert the new cable and plug through the opening for connection in step 6. You may hve access to connector. If so skip to step 8.
4. Remove sliding storage drawer
5. Remove the sheetmetal pan to gain access to the igniter connector. It might help to have several blocks of wood the elevate the frront of the stove to allow more working clearance.
6. Disconnect old igniter, connect new igniter.
7. Replace pan and sliding drawer.
8. Remove old igniter from carrier and install new one.
9. Install igniter carrier to stove with 3 screws
10. Replace flame deflector and lower pan sheild.

The repair actually started online trying to figure out the problem. The parts list and picture provided were a big help. I actually got lucky when I ordered the part. It was a little difficult to get to but once I got the old one out, it was easy and done quick. Saving at least $100 on a repair man was awesome. I had to find the part in the stove first. Then had to find the wiring harness to disconnect. After taking off the back panel and the oven burner plate, the wire harness was exposed. I disconnected, taped on the new wires, remounted the new igniter and put it all back together. Pretty quick and pretty easy.

First, I took out the racks from the oven. Next, I took out the black small square cover off the bottom of the stove, which gave me access to the oven ignitor. Then, I removed the screws to be able to take out the ignitor. Finally, I took the bottom drawer out to access the ignitor wire. I pulled the plastic connectors to disconnect the wire. I took the ignitor out and replaced with the new one. I put everything back in reverse order. The oven warmed up about 2 minutes after I turned it on.

you need to remove the shield then the tray under the burner and burner tube.then you can get to the plug. Just remember when putint it back you need to put the burner tube in first then the tray then you can screw the element back in place. replace all the screws. works great.

I assumed it was the igniter. The trick is to remove the bottom storage drawer for access to where the igniter is connected. You then need to run the wire up into the oven and mount next to the gas.

Thanks to previous reviews it was really easy! Popped cover plate off bottom of oven. Removed diffuser plate by using socket wrench to remove one bolt. Removed three screws (one on top; two on left side) of bracket. Good idea to use a magnetic screwdriver so they don't get lost! Slid igniter out of bracket- a bit tricky but gently eased it out. Slid new igniter in place taking care not to touch the element. Dropped wires and harness down next to old ones. Removed bottom drawer, crawled under and switched connections. Put everything back together. It did take a little longer for the new igniter to start the first time- about one minute- but now fires right up.

Part arrive only a couple of days after ordering, and installation time was less than to schedule a repairman! My only regret is that I didn't send my better half off for the entire afternoon so I could really make it out to be a big deal as my brother-in-law, the appliance repairman, made it out to be!

1.) Trun Off Power
2.) Remove the Storage Drawer and the two (2) screws holding on the (Ignitor Plug) access cover-plate located in the back of the storage drawer access. (see page 15 if same model)
3.) Dissconnect the Ignitor Plug
4.) From the oven opening remove the three screws holding the Ignitor Holder.
5.) Remove the Ignitor and Holder from the oven by gently guiding the wires through the access hole
6.) Pull the Ignitor from the holder
7.) All Ignitors are extremelt fragile; install the new Ignitor into the Holder and make certain it is installed tight, mine was not. (Slight bending with my thumbs on the 1/4" flanges might hold it tighter if it is lose.)
8.)Reverse the process.
Note: One person here said they removed "ALL" the screws, maybe it was a different model, I only had to remove a total of "5" screws, two at the access cover plate and three at the Ignitor holder.
First time took me 20 minutes, if I needed to do it today, maybe 10.
Please also note that I didn't troubleshoot the Ignitor, as I didn't have a wrap-around amp meter, but the typical problem here would be the Ignitor, not the Gas Valve. Good Luck, pt

Removed the bottom drawer then removed the door - 2 screws. It would be hard to reach in oven with door still attached and it is simple to remove and put back on. Removed the racks and pan on bottom, which just lifts out. Removed 3 screws that hold bracket that contains igniter. The igniter plugs in and to access the plug you must remove a cover underneath the range. Once the drawer is out you have to crawl back in there to access the plug. I sent in my 14 year old for that. Make sure range is unplugged. Insert igniter in bracket and feed wire back down to plug in and reattach. Vacuumed oven out with a shop vac, etc. and it is a 30 min project.