ACS3350AB0 Amana Range - Instructions

Thanks to this website I was able to quickly identify the needed part. A few days later I had it. To install the new part I had to open up the bottom inside of the oven to access the igniter assembly and remove the drawer to get to the connecting plug underneath. Four screws needed to be removed, unplugged the old part and plugged in the new part. Replaced the four screws to hold the igniter in place. Replaced the drawer and fired it up. Worked great!

My husband took it apart then showed me how to put it back together. So I placed it in the metal holder and attatched all the screws.

I found the ignitor was wired in series with the gas valve and wasn't letting enough voltage through to the gas valve to open it. I just unscrewed the ignitor and pulled it out.

Turn off power to unit. Remove one nut inside bottom of oven to expose glow bar and igniter. Take 3 screws off of ignitor cover and remove it.

Pull out pan storage drawer to expose igniter plug connector. Unplug connector. Remove igniter.

Plug in new igniter and reverse the above instructions to reassemble.

This was a much easier repair than I thought it would be. I read online that, given the problems my oven was having, it was almost certainly the igniter that was the problem. It was - with the new igniter it works perfectly!

Took cover off inside of oven to expose igniter - 1 nut! - igniter would not glow --3 screws to remove - pulled out storage drawer - un screwed oven shields - (2) - 6 screws - unplugged plastic igniter plug - an replaced! - simple - thank you and made wife buy me dinner for the probably $60 service call! --- thanks to those that posted before me to make this possible!

Removed the bottom drawer then removed the door - 2 screws. It would be hard to reach in oven with door still attached and it is simple to remove and put back on. Removed the racks and pan on bottom, which just lifts out. Removed 3 screws that hold bracket that contains igniter. The igniter plugs in and to access the plug you must remove a cover underneath the range. Once the drawer is out you have to crawl back in there to access the plug. I sent in my 14 year old for that. Make sure range is unplugged. Insert igniter in bracket and feed wire back down to plug in and reattach. Vacuumed oven out with a shop vac, etc. and it is a 30 min project.

My husband did the repair. He removed the wires and screws from the element and replaced with new part.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Once I received the replacement part I simply reversed the process and it worked perfectly.

Removed racks and pans from oven, removed 1 screw that housed the v shaped burner cover. Then I noticed the Igniter housing was held to back of oven with 3 small screws, removed 3 screws, and noticed the igniter just slid into the housing, but the connection would not come through back of unit. pulled out the lower tray to expose the underside of the oven and noticed 2 screws holding a metal cover, removed those and noticed connection to igniter, undid the connection, slid out the igniter and then just reversed the process to put back. It took me about 20 minutes, and that was only because I was being overly careful with the ceramic igniter, as the one in there just crumbled. Very easy job for anyone with even moderate skills. Ordered my part with assitance from a lady at parts express on Monday at noon, had the part delivered Tuesday at 3:00, had the oven back up and running fine by 3:30. Couldn't be happier, as this happened once before and the repairman charged me $185, this cost $48 and 15 minutes.
Unbelievable service and detailed help. I have this site bookmarked for anything moving forward.
Thanks

you need to remove the shield then the tray under the burner and burner tube.then you can get to the plug. Just remember when putint it back you need to put the burner tube in first then the tray then you can screw the element back in place. replace all the screws. works great.

I assumed it was the igniter. The trick is to remove the bottom storage drawer for access to where the igniter is connected. You then need to run the wire up into the oven and mount next to the gas.

First I removed the two screws that hold the element in plance. I then pulled the element out about 3 in ches and disconnected the two wires

I listened to see if the stove was igniting. It was not so we went with the igniter. It arrived in three days. I thin watched a u-tube repair. It was very helpful but looked as if a few steps were unnecessary. After reading the responses decided what steps could be eliminated and carefully replaced the part. It worked the first time. Besides handling the ceramic part very carefully the hardest part was remembering what screws went where! Extremely glad I took this on as a first time stove repair.

The oven door had a stripped thread so I took a knife and held up on washer and unscrewed it. I unplugged the oven. Then slide door off. Then removed pan in oven, then used socket wrench to take off burner sheild (reflector). Then You take out bottom drawer, in the back of opening there is a cover over the connections 2 screws. I unpluged the igniter. Now back in oven the igniter has a cage with 3 screws.. the screw was rusted and frozen. Needed to use WD40 on the screw and let set 10 mins. Now I could remove that screw and other 2 screws. With the cage off I was able to go to bottom where the drawer was and reach in and pull igniter completely out. Becareful not to break the anode it is fragle. ( the black piece) Then reverse and put the new one in. I actually swaped some of the rusty screws that gave me trouble with other screws in the oven that were the same, in case I have to do this again some time in the future. These previous comments from people were greatfully helpful!!!! Thank you!!!

All I would like to say is that I am very satisfied with the service I received from PartSelect.

I definitely would order from them again. By doing the work myself, I believe I saved $80 in labor costs.

Thank you