KP2671 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Gear housing cracked, gear had nic in it
Removed old housing, pulled spring clip, slide on new gear and replaced clip. Put on new gasket and housing. Replaced outer cover. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- walter from SOUTH ELGIN, IL
- Parts Used:
- W11192795
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken gears
Fast
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Madeleine from NEW YORK, NY
- Parts Used:
- WP9706648
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Speed control panel was replaced
Just followed the video.amazing!!got my kitchen aid back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from North Olmsted, OH
- Parts Used:
- WP9706885
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Part broken
Easy thanks to your instructions
Was this instruction helpful to you?
Thank you for voting!
Worm gear stripped.
Remove covers, open gear box, remove lock ring and gears to deterime which gears were bad. Remove old grease, install new gears and pack with new grease.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jamie from Jamestown, ND
- Parts Used:
- W11086780
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
gear teeth worn off worm gear
replace worm gear
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stuart from Pittsford, NY
- Parts Used:
- W11086780
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Gear Stripped was trying to replace
Could not get it properly installed. Had to take to a repair center for completion.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reza from STAMFORD, CT
- Parts Used:
- W11192795
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The mixer started making a loud knocking noise
Unscrew the top and remove it , 4 more screws to remove the top of gear box , wipe out the old grease , lift the gears , but to remove the center gear you need a special narrow tip plier to remove the snap ring . Changed the center gear , apply new food grade grease and with reverse order putting back all remaining parts . Worked fine .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from LARGO, FL
- Parts Used:
- WP9706885
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
white plastic part on the lifter handle
Took off all the screws to open the mixer and install the new parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eileen from GREEN BAY, WI
- Parts Used:
- WP9706648
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Mixer speed control was not connecting properly.
Found a kitchen aid repair video. Found your site for the part I needed. The connections were not like what the video showed but there were enough connector symbols that I was able to understand where they needed to connect. Marking the connections helped for making the new connections when the new circuit board came.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from CASTLE ROCK, CO
- Parts Used:
- WP9706648
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Speed control would go from a "mix" setting 1 to a whip setting "10" by itself.
When I ordered a replacement assembly, I was sent a "new" replacement. As I had read up on your site to number the 5 wires BEFORE I removed them, this was a great idea. The new assembly was wired differently than the original board. Although no install instructions came with the new part, it was just a matter of connecting the NUMBERED wires to the new configuration. The first time I fired it up after plugging everything in, nothing happened! I removed all the plug-in wires and reinstalled to ensure I had not gotten a tight connection because of the plastic covers over the end connectors. On my second try, everything worked as advertised! VIOLA!!!! It was a bit tough because of the tight spaces within the motor housing and the new wire routing. Just take pictures of the area BEFORE you disconnect anything and you should do o.k., since I did. 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from LILBURN, GA
- Parts Used:
- WP9706648
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bad speed control
Thank goodness for YouTube. Pretty much followed the process of taking it out. Was easy, but having a video made it a bit simpler.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRANCISCO from SAN BENITO, TX
- Parts Used:
- WP9706648
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
REPLACE SPEED CONTROL SWITCH
REPLACE SPPED CONTROL SWITCH
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from STRAWBERRY PT, IA
- Parts Used:
- WP9706648
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Speed control switch went out
Unplugged wires from old switch, plugged them into the new switch. The new Switch have the mounting brackets in different places from the old one. Be sure to match up the numbers by the posts with the correct wires
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from PEORIA, AZ
- Parts Used:
- W11086780
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Stripped Gear Mixer would not mix
I have replaced so much on this mixer I can take it apart in my sleep. # speed controllers and now 2 gears. just wish we still had the 40 year old mixer we had, never half as many problems. New are not made like the old.
Was this instruction helpful to you?
Thank you for voting!