WMH1164XVS0 Whirlpool Microwave - Instructions

I placed a thick towel by the opening at the top of my stove and was able to fit the new grease filter in with no problem

After removing the current vent grille I realized one of the three tabs that hold it in place (with the 2 screws) was broken off somehow. This allowed the vent grilled to slide down and into the way of the back edge of the door. It was bending the door edge and I didn't want further damage to the microwave.
I ordered the new part from partselect.com. It came within a couple days.
I opened the door and getting on a stool I could then reach the 2 screws that held the vent grille in place. I remove the screws and the old vent grille. I cleaned the inside of the area with a vacuum to remove the decade of dust and filth... it was pretty bad. (I will probably clean there more often now that I know how to get into it.)
I slid the new vent grille into place and set the screws. It works perfectly.
The stainless color was perfect and looked just like the previous one. The door opens freely now.
Steps:
1- Unplug microwave... always the first step for any repair on an electrical device. Also, be aware a microwave capacitor can hold a charge for a couple days, so be sure to only work on the vent unless you wait a few days for that charge to dissipate.
2- Open the door and get on a stool to find the 2 screws holding the vent in place. They are about 24in apart and screw in on the diagonal.
3- Remove the screws and slide the vent grill out of the tab slots by pulling the top of the vent forward slightly (toward you about 15 degrees) and lifting the vent grill up. The tabs are about 3/8in deep.
4- Clean area. You could blow it out or vacuum. I didn't use any liquid as this is an electrical device and I didn't want to short anything out.
5- Slide the new vent grille into the tab slots. One of the slots is also used by the light cover. You have to slide the light cover as far back as you can (slide the cover towards the back of the microwave) to get the vent grill in without lifting the light cover lid as you slide it in.
6- Place the screws back into the vent grill.
7- Plug in microwave.

I had to cut the leads on the thermostat to enable the wire terminal clips to fit on the leads. Not hard at all when the right tools are available. Care must be used because the leads are subject to being damaged. “ Hold leads with narrow needle nose pliers while cutting!

First, we had to clean up all the interior surfaces, which was just cleaning. There was no internal damage. Then, just setting the center connector, rotary rollers and glass plate. Simple

Took microwave off the mount, removed all the outer covers except the face, used metal screwdriver to short the big capacitor to keep from being shocked, removed magnetron and replaced with new part. Put back together, hung on wall, and finished. I used a youtube video and it turned into a very simple fix.

It took me 15 minutes total - 5 minutes to clean the microwave, 1 minute to install three new parts, and 9 minutes to enjoy my celebratory glass of wine!

Opened door and put new plate in.

Placed order on Thursday evening and received Sat Am

Took out turntable and swapped out old one with a new bright and shiny
New one, ring that is. It was easy using the part from parts select
Thanks
Paul

On top front of the microwave are two Philip's head screws holding the rail on. Remove these screws and the rail snap out the old filter (noting the dark side down) then snapping the new filter in. Replace rail. 10 to 15 minute task.

After removing the over-the-range unit (no small feat!) I had to figure out how to open the case (good puzzle!). Capacitor had already discharged, so it was very easy to reach in, pop the old fuse and install the new one! As per your advice, I found out I was a "28%-er"! Upon re-installation, the microwave "sprang to life"!! Thanks, "Part Select"!! I was already shopping around for a new machine! (Now if you could only tell me an easier way to re-mount this heavy beast over the stove!!!)

Ordered the glass tray and installed it. Received the orderin about two days.

Took out the turntable parts to ensure I ordered the correct cooking tray. Matching those with photos of related parts on PartSelect worked great. Put turntable drive and support ring in place and cooking tray went in very easily. Plan to order a second one to have on hand for this rental property.

Unscrewed glass panel, removed old bulb, cleaned glass panel and installed new bulb. Screwed panel back into place.

Removed the face plate above the door (2 Phillips screws.) Removed existing filter and replaced with the new one purchased. Reinstalled the face plate.

The grease filters you sent to me are not the same size as the filters I replaced!!! Since the new filters do not fit correctly the air does not get filtered since the filters are too small for the hole. Why would you send me replacements that are not the same size as the ones I replaced? The filters are in the hole of the original ones but are too short. Not happy with this transaction at all!!!