WMH1164XVS0 Whirlpool Microwave - Instructions

Took the replacement plate out of the box and put it in the microwave in seconds. I never realized how much of a difference having the correct microwave plate would make. It's great to have it back.

Ordered the item on a Monday at 12pm and it arrived the next day. Amazing!

Simply placed new dish on the rotating hub.

I just opened the box and set it in. Took all of two minutes.

Uncrewed existing screws. Slipped on new vent tighten screws finished

I called the repair/parts number to make sure I had correct parts and the young lady instructed me as to the size of the serving tray; within 48 hours we had the VERY carefully wrapped carton opened and back in the microwave, working perfectly. Thank you. We'll recommend you to our friends!

Stood on a step stool (microwave over stove), took off the one panel,removed old filter and put in new one

removed grill cover, removed bulb plate, unscrew bulb, screw new bulb in socket,put bulb cover back on and screw grill cover back on. no issues whatsoever.

All I had to do was lay the new tray in the microwave. Easy as pie. Also, the new tray arrived very quickly.

1. Safely unplug the dryer. 2. Unconnect the vent hose. 3. Pull it out so you can have room to move around to work on it. I actually in a power chair so I put an old blanket on the floor and laid it face down to work on it. It was extremely dirty so I used a shop vac to clean off the back panel before starting. 4. I took off all the screws and cord cover with a nut driver, used the shop vac again to clean the entire inside. Properly a 1/2 to 1 inch of dust and lint was built up causing a dangerous fire situation for sure. Once clean, take a photos especially of where the electrical connection are. 5 Located and removed the two screws holding the element on, used a nut driver and long nose pliers to remove the heat sensor & electrical connections. 6. Dry fit the element before tightening screws to make sure placement is correct then match the holes replace the screws. 7. Using the photos put the heat sensor & electrial wires back on, you may need to use the pliers to push it on tight. Double check everything, clean back panel inside and out, match up holes replace screws, I actually checked my power cords screws for tightness then replaced cord cover. 8. Replace vent hose if needed or then reattach it and plug it up. You may need to check the dryer barrel by turning the drum around a few times. Should work perfect, you will smell the element a little but it should be ok. Remember clean your dryer inside and out every six months or so to prevent dryer fires.

replaced burnt parts

The problem I have with changing the bulb is my microwave is an overhead one and therefore I cannot tip it on its side to easily replace the bulb. I have to drop the lid down and carefully install the new bulb from underneath.

Watched video which reminded me to order support for the turntable support ring and did exactly what the person in the video did. Excellent and prompt service and all parts fit.

After researching online, I found that I needed the turntable drive coupling, part#PS993087. when I went to your site it showed the same part but the part number had changed but said it would fit my microwave. Well, I was really surprised and happy when the part I received 3 days after I placed the order, with normal shipping,fit perfectly and now my turn table in my microwave works. I have marked this site a a favorite and will use it I'm sure soon. Being a single women and having to figure out how to fix the things on a small buget, I'm learning a lot and have a lot of respect for men that know how to do all the repair stuff. Thanks so much, I have been able to mark this off my list of things to fix. Have a nice day. Cj- age, 58

Removed 2 screws on the top of the microwave and removed top/front piece of microwave. Slid out old filter (which didn't look dirty at all) and replaced it with the new one. Replaced top/front piece and 2 screws. It took less than 5 minutes.