Models > LMV1813ST > Instructions

LMV1813ST (CS1ELGA) LG Microwave - Instructions

Jump to:

All Instructions for the LMV1813ST
16 - 30 of 67
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Thomas from NEWARK, DE
Parts Used:
6324W1A001L
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Would not heat and made a buzzing or popping sound
Unplug the microwave. Remove the Philips head and safety Torx head screws along the bottom of the sides and rear of the microwave which hold the black cover on. Lift the cover up at the rear and slide it backwards to disengage the tabs on the front top. Remove the cover. Discharge the capacitor by shorting the terminals to each other and then ground. Do this with a well insulated object and be aware there may be a pop when you do this. Keep hands, etc. on the insulated part of the object (screwdriver handle, etc). There's a lot of stored energy in that capacitor. I'd advise first checking the diode to make sure its not bad. Replace it if it is. The Magnatron is held in with a couple of screws on the top and sides. Unplug the connector and remove the screws. Remove the Magnatron. Installation is the reverse of removal.
4 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
mark from SANBORN, NY
Parts Used:
6324W1A001L, 6600W1K001D
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
the turn table no turn and no heat the food. but the bottom oven worked
well I unplugged the microwave one day prior to working on it. shock precaution smart way to do this job. very easy pullout the screws behind the unit pull off the outer casing. minor screws inside the unit you have to remove a couple things out of the way. unplug the magnetron and remove first gives you more room to work on the side panel to replace the micro switches. I only replaced one the bottom micro switch. only one bad, but since I was in there I clean the bulb and changed the magnetron any ways. I read other reviews and made my choice to do so. it works perfectly now. Thanks PartSelect for having parts.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Edward from ORCHARD PARK, NY
Parts Used:
6600W1K001D
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Door switch was burnt out
Removed outer cover

removed lower door switch

installed new switch

Wa La!
5 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kenneth from CRYSTAL LAKE, IL
Parts Used:
6600W1K001D
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Items were not getting heated up in the microwave,
I went to LG website enter model number and was given a list of parts that need to be replaced with a percentage of which part fails the most. I order micro switch PS3522738 which arrived and PS3529293 was backordered. I installed the one that arrived. The microwave worked briefly. I reordered and waited for both switches to arrive and installed both. The microwave still doesn't work.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Alan from Moriches, NY
Parts Used:
MCK63604901, MCK62987001
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Both covers were destroyed when the oven was on without any food inside.
Both new parts were installed simply by snapping them into the holes used by the old covers. What I did need was the single round headed push pin used to hold each cover in place after they were snapped into their respective mounting holes but, none were supplied with the new covers. Luckily, I was able to secure the old pins from the damaged parts that I had held onto and used them to secure the new covers. New pins should have been supplied with the new covers.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Raymond from DEPEW, NY
Parts Used:
6600W1K001D
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Oven would not start when closing door.
Removed some cosmetic panels. Removed the assembly with micro switches. Examined the faulty switch by checking the clicking action of switch. Two others were ok by this method. Replaced the switch with new one. Works fine so far. Thanks to web site and YouTube videos.
4 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Cheryl from MATTESON, IL
Parts Used:
MCK63604901
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
I had no problem it was quick simple and very very easy
Just snapped out the old one and snapped in the new one
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Alice from Trenton, NJ
Parts Used:
MCK63604901
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
the stirrer fan cover meltted after I forgot to put the food in microwave and turned the oven on
I received the part and my son put it in where it belonged and no problems
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sherry from PINELAND, SC
Parts Used:
6600W1K001D
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
Door switch malfunction
Take cover off microwave. Check door switches to determine which one was faulty.Remove and replace faulty switch.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
RICHARD from CARY, NC
Parts Used:
6549W1S013H
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
microwave turn table not working
Removed the phillips screws from the base.

Using a # 10 secure driver, remove the motor. (I recommend obtaining a secure star driver set to be sure you have the right size)

Replace the spacer, which is a separate part from the motor.

Reinstall the spacer and motor.

Reinstall the bottom panel.

Enjoy!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kevin from Colonia, NJ
Parts Used:
6600W1K001D
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
suddenly stopped working while in use
i unplugged the unit,unscrewed the outer shell so that all the wiring and internal components were visible.starting at the first of three micro switches i removed the slip on terminals installed the alligator clips too the wires so the switch would now be bypassed.i made sure the wires and clips were not touching anything plugged unit in and it worked.i then installed the new switch and closed up the outer shell
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
thomas from NEWARK, DE
Parts Used:
6912W1Z004B
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
need to replace the Nite light bulb
unplug microwave Remove light bulb hatch unscrew light bulb replaced bulb place bulb hatch back on to microwave plug microwave back in
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Stacie from Granbury, TX
Parts Used:
6324W1A001L
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Microwave would not heat. Convection still worked.
I verified I had 120 volts going into transformer when the microwave was supposed to be running. The capacitor and HV diode both tested good. Be sure to discharge the capacitor before working in this area. This isolated trouble to either the transformer or magnetron. The windings of the transformer measured good. So ordered a magnetron. It was very easy to swap. There were 4 screws and one connector. This fixed our microwave.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Irving from BEDFORD, NH
Parts Used:
MJS47373302
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
broken glass
Just replaced the inner turn table glass tray
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Harvey from COLUMBUS, NJ
Parts Used:
MJS47373302
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Replace broken tray
I opened the door and slid the tray into place.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the LMV1813ST
16 - 30 of 67