RVM225BLC01 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Margaret from Springfield, IL
- Parts Used:
- WB15X321
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
the plastic door handle broke and my husband glued it back on
When the handle broke again, I had to remove the old glue. That part was the most difficult. After that, it was a snap to install the new part. I was a little afraid that I may have ordered the wrong part but there was a 30 day return policy so I went ahead and ordered it. My son was so proud that I had fixed it myself!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Grand Island, NE
- Parts Used:
- WB15X321
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The place where a screw secures the lower portion of the handle, failed.
Removed the two screws (top and bottom) from the interior of the door which allowed the handle to be removed. Positioned the new handle and secured it with the two screws that were used previously
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from Pittsburgh, PA
- Parts Used:
- WB15X321
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic handle cracked near bottom.
Two screws. Too easy.
Was this instruction helpful to you?
Thank you for voting!
Still runs even the door was open
Pulled it from the wall remove the front vent covers removed the control panel remove the door switches by a special screw driver bit which looks a star remove the electrical terminals pressed the plastic clip pulled the switch replaced it with new one then followed initial steps backward
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from TREASURE IS, FL
- Parts Used:
- WB36X10003
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Under the microwave there are two light bulbs that light up the top of the oven/range.
Last week I removed the glass cover that was held in by one screw and removed the burnt out light bulb. I ordered the bulb and left the glass cover off until the bulb arrived. I had to wait until this evening to put the glass cover back on and fasten the screw because I have a window right next to the oven and the sun streaming in made it too difficult for me to see how to put the glass back in and replace the screw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from MAYSVILLE, GA
- Parts Used:
- WB24X830
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave would run but not heat
Removed the control panel, one screw at the top. Removed 2 screws on the door switch holder and removed the door switch. VERY EASY.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MATTHEW from SAN RAMON, CA
- Parts Used:
- WB15X321
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken door handle needed to be replaced
The door handle on the microwave had broken at the bottom fastener, and several glue repair attempts had proved futile over time. After removing the existing handle, I needed to bore the existing hole a little, to remove glue and plastic remnants. So I used a 5/16" drill bit and bored the hole to a depth of about 1/8." Once this was done, I used the existing fasteners and attached the new door handle. No movement in the handle when the door is pulled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from UNIVERSITY PA, MD
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bulb burned out light that is under the microwave, which lights the oven below.
thank you for the video--very clear, responsible, applicable although the illustration was not exactly of our kind of light. the bulb was exactly like the one Hotpoint used in its microwave made in 1989! I will come back to you for parts in the future. (You have the model # from my original order.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Justice, IL
- Parts Used:
- WB36X10003, WB08X10016
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bulb burned out -cracked holder lamp
pluged wires back on ,placed lamp holder and bulb back and replaced screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Ludington, MI
- Parts Used:
- WB08X10016
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Bulb broke in light socket
Tyring to get bulb out i ruined the light socket. Unscrewed the bottom cover of microware. Took out screw holding light socket, removed wires to socket with pliers, intsalled new socket. It was a piece of cake and the part was a perfect match.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Haddam, CT
- Parts Used:
- WB15X321
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Door handle broke off
I used pliers to grasp the remaining door handle stubs and removed the two screws. Then I installed the new handle with the same screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shayla from Tigard, OR
- Parts Used:
- WB15X321
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
One of the two screws that held the handle to the microwave was broken off, leaving a flimsy handle that would probably break completely off soon.
Removed the screws on the inside of the microwave door that held the handle on the front in place. The old, broken handle easily came off. The new piece fix perfectly and we just put the screws back in. Back in service!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Marina Del Rey, CA
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light bulb wouldn't light.
Removed difuser (one screw), removed old bulb, screwed in new bulb, replaced difuser.
Was this instruction helpful to you?
Thank you for voting!
Broken Handle
Removed the 2 screws then the handle and then replaced the handle with the new one and placed the screws. Very easy and did not take much time!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Forest Hills Gdns., NY
- Parts Used:
- WB06X10140
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One support always fell out/ other was fried to the wall
Because of it's age and my memory of it's wall installation problems, I was extremely happy to find the parts. Merely popped the old "fried " support bracket out, snapped it the two replacement brackets and I was back in business with a "new" spark free appliance. Thanks ever so much! Smooth, "no brainer" installation! Extremely pleased with results!
Was this instruction helpful to you?
Thank you for voting!