RVM225BLC01 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jeanne from Kirkwood, MO
- Parts Used:
- WB36X10003, WB08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light bulb burned out and assembly broke when trying to replace bulb
I used the internet and your directions to complete the repair. It was easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Divina from Grand Rapids, MI
- Parts Used:
- WB36X10003, WB08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Both under mount lights were burned out
Unscrewed bottom panel, then unscrewed light socket, then replaced with new socket and bulb. Reattached socket and panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernest from RIVERSIDE, CA
- Parts Used:
- WB24X830
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Unit would run when door is opened
Two screws to remove upper from vent. Two screws to remove the didgit panel lift ip to remove and put aside remove the two screws that hold the door sensors. Depress the tab to remove the defective sensor disconnect the electrical connector and replace the new sensor snap it back into the holder install the two screws, install the didgital panel and vent panel to complete the job. Please be aware that there is a video of this procedure on Y tube
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Enfield, CT
- Parts Used:
- WB27X10240
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
chattering noise/ burning smell
Removed control panel disconnected old capacitor installed new and returned the leads back on to the new. replaced control cover and tested
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cathy from LINCOLN, CA
- Parts Used:
- WB08X10016
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Remove old light sockets and replace in Microwave over stove
Have a microwave that the light and sockets just broke in pieces so I ordered two sockets from this site . The fit perfectly and it was a breeze to install. Took out 7 screws and the plate dropped down, hooked up the little wire which was so simple and bingo I had lite again. I just wished the hold plate came down but it didn't but it was still very easy to install. Will continue to get my appliance parts from this company.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allen from YONKERS, NY
- Parts Used:
- WB6X60
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
While removing for cleaning, grease filter fell behind stove. Could not be retrieved.
Simply slid new part into track holder by hand.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from CHESTERFIELD, VA
- Parts Used:
- WB36X10003, WB08X10016
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no lights on microwave
ordered 2 new sockets and bulbs easy replacement great service from this site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from LOCKPORT, IL
- Parts Used:
- WB6X60
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dirty grease filters
Slide out the old ones then slide in the new ones. A 30 second job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Leesburg, FL
- Parts Used:
- WB36X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
NO light
.Thank You Dan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Batavia, OH
- Parts Used:
- WB08X10016
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Light Socket
Turned the power to the unit off. Removed seven- (7) small screws from the base plate, not removing the rear screws. The plate dropped a few inches allowing me to get to the light socket. I removed one- (1) screw that allowed the socket to be removed. I then detached the two- (2) electrical leads. I now installed the new socket, replacing the leads and the screw along with a new bulb. I pushed the bottom plate back into the up position and replaced the seven- (7) screws. Turned the power back on and we were good to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LUIS from MIRAMAR, FL
- Parts Used:
- WB15X321
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the handle threaded part broke from the handle
Replaced the handle with a new one with only two screws.
At least the original lasted 15 years
At least the original lasted 15 years
Was this instruction helpful to you?
Thank you for voting!
Broken handle
Removed the screw from the broken piece. Put the new handle in the proper location and screw it tight to the door. It is like new now and my wife is very happy to have it ready for the holidays.
Jim Maholic
Jim Maholic
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dawn from yardley, PA
- Parts Used:
- WB15X321
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
our door handle broke off on our microwave
I ordered the part and received it within 2 days, despite my expectations of one week. My husband undid the screws, attached the new handle and screwed it in. It was that simple! And to think that I was ready to phone an appliance repair man!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from Springfield, IL
- Parts Used:
- WB15X321
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
the plastic door handle broke and my husband glued it back on
When the handle broke again, I had to remove the old glue. That part was the most difficult. After that, it was a snap to install the new part. I was a little afraid that I may have ordered the wrong part but there was a 30 day return policy so I went ahead and ordered it. My son was so proud that I had fixed it myself!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Grand Island, NE
- Parts Used:
- WB15X321
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The place where a screw secures the lower portion of the handle, failed.
Removed the two screws (top and bottom) from the interior of the door which allowed the handle to be removed. Positioned the new handle and secured it with the two screws that were used previously
Was this instruction helpful to you?
Thank you for voting!