JVM1330BWC02 General Electric Microwave - Instructions

The Parts select diagram and order ing process made it very easy to complete my repair job. After receiving my parts, I unscrewed the screws with a phillips driver. Then I popped out the handle. There is one tricky part - the screw is a bit too small for the existing whole and so I added a washer to fix this problem. I then slide in the new handle. Very easy!

My microwave is built in above the stove which provides lighting and fans for my stove. The glass lens cover for the lighting was cracked in several places and the light bulbs had burned out. I taped the glass lens for removal so it didn't break apart due to the cracks Removed the one screw. .Both light bulbs broke away from the base sockets as I tried to unscrew them. I used electrical tape wrapping in reverse on a lightbulb (socket end) so it was sticky for a grip on the base, shoved it in the sockets and was unable to unscrew the broke off bases. So it was very successful and no repair man was needed.

Very easy repair to replace filters. Step 1: Note position of filter and which end is towards you and position of latch handle. Slide old grease filter away from you and forward until it drops out, Set it aside. Step 2: Take new filter and put in slot away (as you noted) from you then slide towards you until seated properly underneath microwave. Repeat steps for the second filter. It takes about 2 minutes.

.Thank You Dan

Did as describe by others who had replaced the handle.
Remove the inside trim (carefully) to get access to screws that we holding the remaining handle pieces.
Attach the handle with the exist screws, replace the trim. Done in about 5 minutes.

I first pulled the bottom left and left side inner 3/8th inch rounded liner out. Use a thin flat head screw driver to gently pry the inner trim piece out of place. This exposed the bottom screw. I pulled out the old 1/2 inch silver coarse thread screw. The top screw is obvious. Removed that. I had to replace the face plate which slid off. Replaced the new face plate then put in the new handle top male end then the bottom male end in the holes. I screwed in the top 1.5 inch browm fine thread screw. Don't over tighten, just go until snug. If you over tighten you may crack the plastic walls of the screw hole built into the handle. I then put the small screw in and tightened it. Then snap the trim piece back in place. Viola.......You are done

Have a microwave that the light and sockets just broke in pieces so I ordered two sockets from this site . The fit perfectly and it was a breeze to install. Took out 7 screws and the plate dropped down, hooked up the little wire which was so simple and bingo I had lite again. I just wished the hold plate came down but it didn't but it was still very easy to install. Will continue to get my appliance parts from this company.

ordered 2 new sockets and bulbs easy replacement great service from this site

I first read the previously posted directions from other customers that were sent with my part order confirmation, which were all very helpful. Then, I basically used a screw driver to unscrew the screw holding the lens cover in place - be careful as it is a very tiny screw and it can easily fall behind your oven. You might want to place a large piece of cardboard over the space between oven and wall, as I did, so that you don't lose the screw in case it falls. Next I pried open the prongs, carefully slid out the cracked lens, and slid the new lens in place, pushed back the prongs and put the screw back in. I found that it was easier to use my fingers to first place and tighten the screw because it is very small and will keep falling out of place if you try to just use the screwdriver. Good luck!

Turned the power to the unit off. Removed seven- (7) small screws from the base plate, not removing the rear screws. The plate dropped a few inches allowing me to get to the light socket. I removed one- (1) screw that allowed the socket to be removed. I then detached the two- (2) electrical leads. I now installed the new socket, replacing the leads and the screw along with a new bulb. I pushed the bottom plate back into the up position and replaced the seven- (7) screws. Turned the power back on and we were good to go.

unsrew top handle screw on inside of door, removed handle, slid handle plate out slid new one in (probably would not have had to replace this part but the part makes the job look better) removed snap in trim finish around window inside door, fished out old screw and broken plastic from handle, srewed new handle on, snapped trim back on and job was complete.

removed the interior door seal with thin scraper. Then removed screws. Replaced "new handle" and reverse process. Process is easy but the handle part is ridiculously expensive for what it is!

Simply removed screw, pulled down light holder, unfoled the metal tabs, took out the broken pieces and replaced the glass lens and light bulb.

unscrewed the screw, pried up metal tabs that hold in light lens. took out broken pieces, slid in new light lens re-secured tabs with fingers, screwed in the screw again.

Removed three screws from the top front cover and slide it out and following I removed the touch panel and the housing that holds the switches and replaced the bad one.