JEM25DM2BB General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ernest from RIVERSIDE, CA
- Parts Used:
- WB24X830
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Unit would run when door is opened
Two screws to remove upper from vent. Two screws to remove the didgit panel lift ip to remove and put aside remove the two screws that hold the door sensors. Depress the tab to remove the defective sensor disconnect the electrical connector and replace the new sensor snap it back into the holder install the two screws, install the didgital panel and vent panel to complete the job. Please be aware that there is a video of this procedure on Y tube
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LAURA from GALVESTON, TX
- Parts Used:
- WB06X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Microwave missing a roller guide
When we bought our house, the microwave was missing a 'roller guide'. I didn't know that part even had a name, but your website made it easy for me to figure out. When it arrived, like the next day - I just unpacked it and placed it inside the microwave. Done! Thanks for the help!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dave from warrendale, PA
- Parts Used:
- WB06X10489
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
broken catches on the door
took the door off then poped off the plastic ring around the door then installed the new part.job was real easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from E PATCHOGUE, NY
- Parts Used:
- WB06X10304
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Roller stems wore out; rollers fell off
Open door. Remove tray. Remove old roller assembly. Insert new roller assembly. Replace tray. Close door. It took more time and effort to unpack it than it did to replace it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billy from SWANNANOA, NC
- Parts Used:
- WB49X10097
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The old plate got broken
Just open door and install the new cooking tray in the grooves.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from COVINGTON, GA
- Parts Used:
- WB20X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bad thermostat
Removed outer case, checked fuse first, it was good so went to thermostat. No continuity reading. Unhooked thermostat, used jumper wires to by-pass break—briefly plugged the unit in. It came on so I knew the issue was definitely the thermostat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Muncie, IN
- Parts Used:
- WB24X829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
microwave Quit working but lights worked
llation
Was this instruction helpful to you?
Thank you for voting!
Still runs even the door was open
Pulled it from the wall remove the front vent covers removed the control panel remove the door switches by a special screw driver bit which looks a star remove the electrical terminals pressed the plastic clip pulled the switch replaced it with new one then followed initial steps backward
Was this instruction helpful to you?
Thank you for voting!
Microwave will not start
Removed three screws from the top front cover and slide it out and following I removed the touch panel and the housing that holds the switches and replaced the bad one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Igor from Delray Beach, FL
- Parts Used:
- WB27X10985
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
No power, no lights, did not work
Relatively simple for skilled person.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from MAYSVILLE, GA
- Parts Used:
- WB24X830
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave would run but not heat
Removed the control panel, one screw at the top. Removed 2 screws on the door switch holder and removed the door switch. VERY EASY.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Shawnee, OK
- Parts Used:
- WB24X829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
time would count down but unit would not run & heat.
remove cover, unplug secondary door switch (top switch)
remove switch from holder, install new switch, plug in wires, replace cover, very easy. door switches are a common problem
with microwave ovens.
remove switch from holder, install new switch, plug in wires, replace cover, very easy. door switches are a common problem
with microwave ovens.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebecca from Syracuse, NY
- Parts Used:
- WB06X10723
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
door hinge was loose, appeared to need something to stabilize
I could not do the repair. The clip that I ordered did not go in the bottom hinge, but rather in the top hinge, which was not broken. I could not figure out how to repair it. There was no other part in the diagram that looked as though it would solve the problem, so I needed to buy a new microwave. A more detailed drawing would have been helpful--one that showed how the hinges were attached and how they worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Shawnee, OK
- Parts Used:
- WB24X829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven wouldn't heat
remove cover-unplug wires from secondary switch-remove switch-snap in new switch-plug in wires-replace cover-works great. very easy to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Mountain View, AR
- Parts Used:
- WB24X829
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave worked but oven fan came on when door was opened - should onlly come on when oven is operating.
Removed the microwave with the buit in housing from the cabinet. Removed microwave from built in housing. Removed outer cabinet giving access to remove control panel and smart board where switches are located. Removed control panel to get to smartboard. Removed smart board after disconnecting a few wires to allow easy removal. Individually removed and then tested each switch using multimeter. Found seondary Door Switch (bottom of smart board) operation to be intermittent (switch trip button extremely loose and rattle inside this particular switch) Ordered replacement part which came very quickly on standard shipping order. Put new switch on smart board and remounted, reinstalled control panel and reconnected various wire connectors previously disconnected. Then plugged in oven and tested for opertation - didn't work at all! But, after bleeding off capacior charge by removing connectors and discharging capacitor to ground, then reassembling control board and smart board into oven, then trying agian, it has worked perfectly ever since. Do not understand why capacitor disconnect/discharge was required but suspect this reset the control electronics. Easy fix and hope to get another 12 years out of this appliance which is used multiple times every day. Also have two other identical micorwave ovens, one is 20 years old, but these get used relatively infrequently.
Was this instruction helpful to you?
Thank you for voting!