SCA1000DBB03 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Esther from Brooklyn, NY
- Parts Used:
- WB06X10311
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
cover fell apart
removed screw from inside wall. removed leftover board & replaced with new board & screw. good as new!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mack from Jacksonville, FL
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
No heat.
Replaced the fuse. Result; did not fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benjamin from Anchorage, AK
- Parts Used:
- 6324W1A001L
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replacement of Magnetron
I UNPLUGGED the microwave and removed the cover, using a phillips and a Torx screwdriver for the machine screws. I set these screws aside, so as not to confuse them with the later encountered screws. I photographed the magnetron to assure proper placement of the 6 phillips machine screws involved in reassembly (marking the the locations on the old magnetron would do as well. I marked the old magnetron "old", to avoid later confusion. I removed the two screws holding the shields to the magnetron. I removed 3 of the 4 screws holding the magnetron to the microwave, leaving one of the top screws. I held the magnetron securely and removed the last screw, pulling out a the part of the magnetron that penetrated the microwave. I installed the new magnetron in reverse order. One problem I encountered was locating one of the six screws, which had been pulled into the old magnetron by magnetism.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from New York, NY
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No heat
Replace the fuses
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nelia from Streamwood, IL
- Parts Used:
- 6324W1A001L
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
no heat
unplug the unit then pull down , lot of screws are on top. open the cover . you could see the parts that need to replace on the right hand side (heavy side). disconnect wires then test the parts that need to replace by a tester to make sure that it's really broke .then unscrew part and replace .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clifford from Springfield, VA
- Parts Used:
- WB10X10021, WB06X10216
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
install new latch and spring in door
removed key pad then removed latch assembly and replaced it with new latch assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Raleigh, NC
- Parts Used:
- WB15X10069
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Broken Door handle and latch
Part delivered in2 days - awesome!Used the putty knife to get under the tabs to pull the cover shield off to get at the door "innards". Needed to take the underpanel out 6 small phillips head screws - non-magnetic so be careful you don't lose them.Pulled the shield of and the door comes away. Becareful not to drop it. Handle and latch went on quickly and as expected - put parts back in reverse order and off yuo go. Door works as good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mohammad from Piscataway, NJ
- Parts Used:
- WB27X10928
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Powered Off completely
After reading reviews that there was no power what so ever and a fuse replacement will solve the problem, I tried it. Replacing the fuse is very easy (and I am not handy at all). All you have to do is remove the microwave cover from the top by removing two screws, slide the cover to the left and pulling the cover off. Then remove the grill in front of you, by removing one or two screws. The fuse is in front of you, use pliers and be firm but gentle. Replacing the fuse is easy but it did not solve my problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicole from Lathrop, CA
- Parts Used:
- WB49X10129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
drop and shattered the glass tray
It was so easy to order the part on this website. It came carefully packaged and quickly! Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Socorro, NM
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Quit working
Just like the directions said. Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from San Marcos, CA
- Parts Used:
- WB49X10129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken micro tray
placed plate on carousel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rong from Portland, OR
- Parts Used:
- WB20X10048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
circuit shortage shows, i thing it because i heat on the counter too long cause the thermotart not fumctional.
it work ok now
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph F from Clarkston, MI
- Parts Used:
- WB03X10131
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob became worn.
Couldn't find the exact part using the online service but called and the customer service operator got me precisely what I needed - she was fast, friendly and very helpful. I had a great overalll experience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ISAAC from MADAWASKA, ME
- Parts Used:
- WB49X10129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Glass Tray
Very easy replacement. Just lift out and replace with a new one!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from Puyallup, WA
- Parts Used:
- WB49X10129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass tray broke in microwave
Removed tray from shipping container and installed in the microwave.
Was this instruction helpful to you?
Thank you for voting!