SCA1000DBB03 General Electric Microwave - Instructions

Very easy replacement. Just lift out and replace with a new one!

No description of repair method with part, or in owner's manual, so I YouTubed the subject. Outer plastic covering was easy to remove by prying off with screwdriver. Be careful not to break clips. Removing door assembly from body was easy- Just lift off of hinges (but you need to remove fan grille at top of microwave first-simple). Removing metal inner door casing to access handle screws was a bit more difficult as you had to remove 6 small screws and then pull the casing from about 8 plastic brackets that hold casing around perimeter. Have to be carefull not to break the brackets. Once that was removed it was easy. With access to door handle screws now visible simply unscrew, remove old handle pieces and reinstall new handle using same screws.

I went on line and found the part and read all the comments that had been written on how to repair the door and I found the directions on how to take it off and put it back on, so it helps to do your research on taking it off and putting another one. My son-in-law did it for me, it was quite difficult to remove the screws,and it took about 30 min to remove the door and take the screws out, but putting it back on was easy and took less than 5 min. So I was pleased, the part was ordered on Sat and came by FX on Tuesday, I was very happy with the service, and it works as good as new. Just do your research, that helped a lot.

I pulled out the unit and found 2 interlock switches that are depressed when the door closes. After cycling the door open/closed I found that one of the switches occasionally would stay depressed. The repair was easy (after I took off the panels so I could get to the switch) I simply removed 2 screws that attached the interlock switch assemblies to the main unit. Then I popped out the defective switch and popped in the new one. This did indeed fix my problem.

Called my local appliance repair shop when the handle broke off my GE Advantium microwave. They told me the price of the handle, but said the door would need to be replaced as well. This is because the plastic tabs break off the inner door panel when it is removed. They estimated a $400 repair cost. I ordered the door and installed it for around $45. The inner panel comes out, and most of the tabs do break off. I was able to disassemble, install the new door, and reassemble. The inner panel stays right where it belongs, even though I broke off a few plastic tabs. Werks goood.

Unpacked glass plate from cardboard box and placed atop rotating spindle inside oven - done.

My son said order it. It came a day later. Very cool. He took the door off and up to his room. No idea what tools except most likely a screwdriver. I asked him how did it go. He said it's good. Nice...

Snap the plastic trim piece from the inside of the door off.took broken latch out and put the new one in.PS your part came really fast.Thanks

First I called General Electric and was told they had the vent grille part and would ship it for $95.00. I then went on line and found the same part number at PartSelect.com. They quoted me a price of $75.00 and I purchased it on line. It arrived within 3 days and had the new vent grille on my G.E. Profile Oven/Microwave within 30 minutes of opening the box. All I did was remove the two screws from the broken grille, removed the grille and put on the new vent grille with only a screwdriver. I highly recommend Parts Select as they exceeded my expectations.

the plastic liner was re moved to expose the handle screws.the top screw was acessable and removable. the bottom screw was behind the metal support of the protective window.I used a over size metal bit in my drill to expose the screw head holding lower part of the handle. The screw was removed and the hole cleaned out for the replacement handle. job was completed

I'm writing because I have never in my life had such an easy time finding a part, ordering it, and receiving it! Your service is truly unbelievable. I still don't believe it and I experienced it. Nothing went wrong and it could not have been easier. Please don't go away.

After reading reviews that there was no power what so ever and a fuse replacement will solve the problem, I tried it. Replacing the fuse is very easy (and I am not handy at all). All you have to do is remove the microwave cover from the top by removing two screws, slide the cover to the left and pulling the cover off. Then remove the grill in front of you, by removing one or two screws. The fuse is in front of you, use pliers and be firm but gentle. Replacing the fuse is easy but it did not solve my problem.

This is the tray the glass cooking tray rest on and rotates the glass during cooking. The metal tray was installed upside down. The rotating glass tray was not properly installed. The oven was at a very high temp. and the weight of the utensil on the glass was not supported correctly. Result, big " pop " and broken glass tray. Note this is the second glass repaced. The first one dropped while removing it from the oven. It stuck to the bottom of the cooking dish and then fell to the floor. Pop, big breakage. Maybe you can learn from my mistakes.

It was so easy to order the part on this website. It came carefully packaged and quickly! Thank you!

opened the access door. It took some tugging to get the old bulb out, and is was awkward getting the prongs on the replacement bulb lined up and pushed in, but it was accomplished in about 10 minutes. You had exactly the right information on a change in the part number that was made by GE, and you shipped the correct bulb the same day I ordered it.Good job. N R Brown