JVM1490BD003 General Electric Microwave - Instructions

the problem was the mounting bracket that was installed when the house was built ,was not the bracket that came with the microwave. It was used to step the microwave out 3" in front of the other cabinets for the style that they were using then. so when I was installing the new cabinets I didn't want that style, so I ordered the original mounting bracket. It was a perfect fit and the install went great

Removed inner trim panel. Bottom screw was visible But upper screw was behind metal frame that trim plate snaps onto Removed that to access screw. Door latch had to be removed to. Not a big deal just be sure spring on latch is reinstalled same way it was removed. Took longer than expected but way cheaper than a service call. Part arrived on time

Removed plate inside door cover and removed old screws and plastic handle. Reassembled.

removed screw from inside wall. removed leftover board & replaced with new board & screw. good as new!!!

Replaced the fuse. Result; did not fix the problem.

I UNPLUGGED the microwave and removed the cover, using a phillips and a Torx screwdriver for the machine screws. I set these screws aside, so as not to confuse them with the later encountered screws. I photographed the magnetron to assure proper placement of the 6 phillips machine screws involved in reassembly (marking the the locations on the old magnetron would do as well. I marked the old magnetron "old", to avoid later confusion. I removed the two screws holding the shields to the magnetron. I removed 3 of the 4 screws holding the magnetron to the microwave, leaving one of the top screws. I held the magnetron securely and removed the last screw, pulling out a the part of the magnetron that penetrated the microwave. I installed the new magnetron in reverse order. One problem I encountered was locating one of the six screws, which had been pulled into the old magnetron by magnetism.

removed key pad then removed latch assembly and replaced it with new latch assembly.

Replace the fuses

unplug the unit then pull down , lot of screws are on top. open the cover . you could see the parts that need to replace on the right hand side (heavy side). disconnect wires then test the parts that need to replace by a tester to make sure that it's really broke .then unscrew part and replace .

Removed outer cover and then replaced the T. C. O. located on the left upper side if the unit. Replaced outer cover, tested oven. Oven operates normally.

The instructions were great!!! It was difficult to take the face plate off without breaking the nibs off that hold it in place. Other then that the only issue I had was removing the broken piece that was cemented in place by the years of super glue. Had to drill it out and almost drilled out the receiver plate to hold the screw/handle in place. I have to say this saved me $400 because I was just about to buy a new microwave because the broken door handle had driven me crazy over the last 3 years.

This wasn't easy to do, it would have been better to have two people. Taking the plastic trim off the inside of the door is tough, and only gets you access to the top screw. (You need to take that trim off to remove the door, and you have to put the door back on before you put the trim back, by the way.) You have to remove the shield covering the glass in order to get to the bottom screw. I didn't think I'd be able to get that shield off, and another set of hands to help pry it up would have been helpful. All in all, it's worth doing because the part is only $40 or so, but I can't call it an easy fix. Also, since the top of the handle had broken where the plastic screw sleeve meets the handle, and the screw was still inside the sleeve, it was almost impossible to get the screw out. Needlenose pliers wouldn't do it. I finally had to use a drill to drill away at the plastic sleeve until it was almost completely gone to get the screw out.

Remove door from unit. Place on cushioned service. Carefully pry plastic frame on inside of door to expose upper screw hole for handle. To gain access to lower screw hole, the inner metal frame must be removed. First, remove screws holding metal frame to door. Now carefully pry back the plastic tabs on each side. Once tabs are freed, metal frame easily removes. Install new handle, snap metal frame back, reinsert metal screws, then resnap plastic frame into place.

I removed the plastic perimeter molding from inside of door.You can carefully pry it loose with a narrow putty knife. the door handle screws are located directly behind were the handle attached to the outside of the door. I found that a #2 phillip head screwdriver tip with a large handle for good torque and grip works best however the old plastic post inside the face of the door were turning along with the screws from the opposite side. I used a needle nose plyers to hold onto the plastic barrels in the outside of the door while turning the phillips head screwdriver on the inside at the same time. I found this to be somewhat difficult.You must achieve a good bite with the pliers!

First unplugged the microwave, took top grill off, took control panel off, took wires off and used color coded tape to make sure they went back in right places, took fuse out and replaced it and put every thing back and it all worked fine and to top it off my wife did it all. So it was pretty easy.