JVM1490WD002 General Electric Microwave - Instructions

bought a fuse but that didn't solve the problem. Guess I need a new microwave

opened the access door. It took some tugging to get the old bulb out, and is was awkward getting the prongs on the replacement bulb lined up and pushed in, but it was accomplished in about 10 minutes. You had exactly the right information on a change in the part number that was made by GE, and you shipped the correct bulb the same day I ordered it.Good job. N R Brown

PartSelect had helpful repair instructions on-line which made the repair easier and faster. Unfortunately, there were other problems with the oven that immediately blew the new fuse I had just installed. It was then determined that additional repair would most likely cost almost as much as a new microwave.

After reading reviews that there was no power what so ever and a fuse replacement will solve the problem, I tried it. Replacing the fuse is very easy (and I am not handy at all). All you have to do is remove the microwave cover from the top by removing two screws, slide the cover to the left and pulling the cover off. Then remove the grill in front of you, by removing one or two screws. The fuse is in front of you, use pliers and be firm but gentle. Replacing the fuse is easy but it did not solve my problem.

Plastic broke off where the screws are inserted.

Removed outer cover and then replaced the T. C. O. located on the left upper side if the unit. Replaced outer cover, tested oven. Oven operates normally.

On March 21st my wife's daughter and husband and I tackled the repair. I am physically limited, so their help was not only welcomed but necessary.First, removed two screws on the top of the oven to remove the vent panel. Then removed the door by lifting up (as described by others). Next removed the black plastic trim from around the window, using a table knife to pry it loose. Broke off some of the clips but that proved to be no problem at reinstallation. Removed 6 small screws holding the window assembly, but we were unable to pry the plastic tabs loose and we never were able to remove the panel. The screw to the upper end of the door handle is exposed and easily accessible. The screw holding the lower end of the handle is underneath the metal window assembly. We drilled a hole in the metal assembly until the screw was exposed. Removing the screw was a major undertaking. The housing in which the screw was imbeded would not release the screw. We used the drill with a small bit to drill the plastic out until the screw came free. It was difficult and tedious and time consuming. After finally releasing the two screws we began installation of the handle. We found the female receptacle on the handle was very reluctant to accept the screw, both top and bottom. The job was eventually completed after we lubricated the female receptacle adequately. Even so the handle is not quite a snug as I would have liked to have it.The job was hard, tedious, and took over two hours. reinstalltion of the door was no problem. I don't believe the designers and manufacturers intended amateurs to make this repair

Our GE Profile Advantium 120 Series Over-the-Range Microwave stopped working. We called GE Service. The first available appointment was two weeks after our call. The technician charged $99, gave us a form stating that the Magnetron and Diode Cable as defective and quoting an additional price of $362 to furnish and install these parts. He said that it would be another two weeks before he could do the work. Instead I ordered the parts from you and had them within two days. The parts you furnished were identical to the original parts in our unit. They arrived within two days. I installed the parts without removing the microwave from the wall. The most difficult part was inserting the magnetron mounting screws into openings in the rather tight space available. I was able to do this by using plastic pacaging tape to hold the screws onto the end of a short Phillip screw, Prior to iserting each screw I pushed it through the sticky side of a piece of packaging tape. I then folded the sticky surface over the shank of the screw. Once a screw was seated, but before it was fully tightened, I used needle nose pliers to pull off the tape. The unit now functions perfectly.

Removed cover, diagnosed problem, ordered part from Parts Select, received part in 2 days, replaced part, tested and replaced oven into built in space.

First unplugged the microwave, took top grill off, took control panel off, took wires off and used color coded tape to make sure they went back in right places, took fuse out and replaced it and put every thing back and it all worked fine and to top it off my wife did it all. So it was pretty easy.

Remove choke,then remove glass, then replace handle reinstall in reverse

Read instructions and viewed video. Project would have been very difficult without the instructions and video. Step 1 removed vent grill at top to microwave, by removing two scres. Step 2 removed microwave door by lifting. Step 3 used a one inch plaster knife to separate the plastic interior cover of the door. The video was most helpful. Use the thin blade of the plaster knife to locate snap locations of the plastic cover. Step 4 removed broken latch by applying slight pressure to the outside. Observed the attachment of the 'spring'. Step 5 installed new latch and spring. Step 6 reinstalled interior plastic cover. Step 7 install door. Step 8 install vent cover with two screws. Step 9 test unit.

The Vent Grill came off when the two Tabs crack and broke off. The New replacement from PartSelect arrivied. Took the part out of package and replaced the two screws on top of the Vent. Had to push the Vent in to align the first screw. Pushed the side of the vent to align the Tab and put the second screw in. The fit was perfect

Removed. Inside frame with putty knife replace new latch attach spring and line up notch of latch in slots. That was the most difficult part replace inside frame. Done!

Take the pliers and place a tight grip on the broken rack bracket, twist toward front of microwave until loose, pop out and by hand insert new rack bracket, twist toward the back of microwave until fully in place. One side was slightly harder than the other taking off and replacing rack bracket.