Models > JVM1490WD002 > Instructions

JVM1490WD002 General Electric Microwave - Instructions

Jump to:

All Instructions for the JVM1490WD002
91 - 105 of 172
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
wayne from Belmont, CA
Parts Used:
WB15X10070
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
replaced broken handle
Look carefully at the blow up of the inner ring or you could break the tabs tryig to get it out. I missed seeing the tabs on that blow up and I broke many of the tabs on the inner ring. I assumed they were on the outer rim of that ring when in fact they were on the inner edge.

Fortunately there were enough locking tabls left to reuse that part.

I hope the new design of your door handles strengthens the bottom attachment as it is the weaker of the two attachment points and yet it gets the most force as most people will pull down on the over head handle rather than straight out.
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Edwin from New York, NY
Parts Used:
WB27X10928
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
No heat
Replace the fuses
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Clifford from Springfield, VA
Parts Used:
WB10X10021, WB06X10216
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
install new latch and spring in door
removed key pad then removed latch assembly and replaced it with new latch assembly.
3 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Nelia from Streamwood, IL
Parts Used:
6324W1A001L
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
no heat
unplug the unit then pull down , lot of screws are on top. open the cover . you could see the parts that need to replace on the right hand side (heavy side). disconnect wires then test the parts that need to replace by a tester to make sure that it's really broke .then unscrew part and replace .
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lewis from Jupiter, FL
Parts Used:
WB15X10070
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Broken off door handle
Remove upper vent (2 screws) lift up on door after opening. Door will come off pretty easily. Slide putty knife between parts and remove. Take out screws and replace handle with the original screws. Reverse procedure rehang door and become a hero to the bride. Don't worry about the snapped off tabs. There will be enough of them left to hold everything together.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Yvonne from Melbourne, FL
Parts Used:
WB15X10070
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Broken Door Handle
Parts select made the ordering very easy and the exact part arrived shortly after ordering. I would suggest following ALL the suggestions to a tee that others have written in. Removing the entire door (a suggestion) was definitely a good idea. I had to do some 'extra' rigging because one of the plastic screws was also broken and that is actually part of the door..........and I would have to replace the entire door ($$$).......didn't want to do that. "DO" be careful when removing the little clips....that is a little tricky but do-able......IF you take your time. THANKS for all the other people before me that wrote in their hints...I did listen to my wife and read them all before I started. Good luck.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Esther from Brooklyn, NY
Parts Used:
WB06X10311
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
cover fell apart
removed screw from inside wall. removed leftover board & replaced with new board & screw. good as new!!!
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Benjamin from Anchorage, AK
Parts Used:
6324W1A001L
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Replacement of Magnetron
I UNPLUGGED the microwave and removed the cover, using a phillips and a Torx screwdriver for the machine screws. I set these screws aside, so as not to confuse them with the later encountered screws. I photographed the magnetron to assure proper placement of the 6 phillips machine screws involved in reassembly (marking the the locations on the old magnetron would do as well. I marked the old magnetron "old", to avoid later confusion. I removed the two screws holding the shields to the magnetron. I removed 3 of the 4 screws holding the magnetron to the microwave, leaving one of the top screws. I held the magnetron securely and removed the last screw, pulling out a the part of the magnetron that penetrated the microwave. I installed the new magnetron in reverse order. One problem I encountered was locating one of the six screws, which had been pulled into the old magnetron by magnetism.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mack from Jacksonville, FL
Parts Used:
WB27X10928
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
No heat.
Replaced the fuse. Result; did not fix the problem.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Stephanie from Kernersville, NC
Parts Used:
WB27X10928
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
microwave won't heat
bought a fuse but that didn't solve the problem. Guess I need a new microwave
Was this instruction helpful to you?
Thank you for voting!
Customer:
Peter from Madison, AL
Parts Used:
WB55X10428, WB10X10021
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Oven would not operate after we noticed that the catch inside the door was broken
Removed the door, removed the old choke cover (breaking all the stap catches), removed the slide door latch assembly from the spring (the most difficult task) then reassembly of the latch to spring, sliding into the grooves along the inside of the door, the installing the new choke cover (very easy with the new one) taking care not the break any of the staps. Easy enough! Another difficult task was to re-install the door to the frame. It appears that the lower "hinge" is slightly bent down to allow easy install but the door now makes a slight sweeking sound when opening and closing.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mark from Meridian, TX
Parts Used:
WB10X10021
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
broken door latch
I held the door open while the repair man took the black facing off and replaced the latch and reinstalled the facing I was worn out
Was this instruction helpful to you?
Thank you for voting!
Customer:
ed from virginia beach, VA
Parts Used:
WB06X10311
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
replace plate
removed cover an replaced
Was this instruction helpful to you?
Thank you for voting!
Customer:
Steven D from Seminole, FL
Parts Used:
WB49X10129
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Broken Glass Cooking Tray: need replacement part
Took item from sealed box and removed protective bubble wrap. Placed tray in microwave, aligning tray with turntable sprockets. Perfect fit, perfect match! And the part arrived in three days and was very competitively priced. What more is there to stay? Will use PartSelect for other replacement parts. No brainer!
Was this instruction helpful to you?
Thank you for voting!
Customer:
ISAAC from MADAWASKA, ME
Parts Used:
WB49X10129
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Broken Glass Tray
Very easy replacement. Just lift out and replace with a new one!
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JVM1490WD002
91 - 105 of 172