Models > LMH2235ST > Instructions

LMH2235ST (00) LG Microwave Oven Combo - Instructions

Jump to:

All Instructions for the LMH2235ST
46 - 60 of 64
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Robert from Cedar Park, TX
Parts Used:
6600W1K001D
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Microwave failed to head and light, fan, and turntable failed to come on.
Problem was due to a faulty door switch. Replaced with a new switch and the microwave now works fine! Only thing that was tricky was that LG uses the hex screws with a peg in the middle to keep the microwave cover on. Had to use a small screwdriver and pliers (on the screwdriver) to unscrew the screws.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Nelia from Streamwood, IL
Parts Used:
6324W1A001L
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
no heat
unplug the unit then pull down , lot of screws are on top. open the cover . you could see the parts that need to replace on the right hand side (heavy side). disconnect wires then test the parts that need to replace by a tester to make sure that it's really broke .then unscrew part and replace .
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Benjamin from Anchorage, AK
Parts Used:
6324W1A001L
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Replacement of Magnetron
I UNPLUGGED the microwave and removed the cover, using a phillips and a Torx screwdriver for the machine screws. I set these screws aside, so as not to confuse them with the later encountered screws. I photographed the magnetron to assure proper placement of the 6 phillips machine screws involved in reassembly (marking the the locations on the old magnetron would do as well. I marked the old magnetron "old", to avoid later confusion. I removed the two screws holding the shields to the magnetron. I removed 3 of the 4 screws holding the magnetron to the microwave, leaving one of the top screws. I held the magnetron securely and removed the last screw, pulling out a the part of the magnetron that penetrated the microwave. I installed the new magnetron in reverse order. One problem I encountered was locating one of the six screws, which had been pulled into the old magnetron by magnetism.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ernest from Jacksonville, FL
Parts Used:
MJS47373302
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Glass tray broken
really easy
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Denise from NORTH BEACH, MD
Parts Used:
6930W1A003X
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Thermostat needed to be replaced
We had made this determination with the help of a repairman on the phone. I ordered the part and waited for it. It was stuck in West Virginia. After several days after it was expected a repairman fixed my range to the tune of $168. It should have cost $30 (the cost of the part and shipping).
Unfortunately I probably won't order from PartSelect again.
8 of 27 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Marianne from CHURCH HILL, MD
Parts Used:
6912W1Z004B
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
light bulb replacement
very simple
9 of 31 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Don from Palo Alto, CA
Parts Used:
MCR62347202
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Socket set
broken plastic fan facia
removed MW disassembled the fan slide and installed.
10 of 40 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Craig from Burke, VA
Parts Used:
6912W1Z004B
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Light bulb burned out
I unscrewed the light cover, removed the burned out light bulb and replaced it with one I ordered on Partselect.com. It was very easy.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the LMH2235ST
46 - 60 of 64