Models > JBV42G*J1 > Instructions

JBV42G*J1 General Electric Microwave Oven Combo - Instructions

Jump to:

All Instructions for the JBV42G*J1
91 - 105 of 122
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Jerry from Copperas Cove, TX
Parts Used:
WB30M2
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
No Problems
I removes the old element and drip bowl, then replaced the drip bowl, then replaced with the new element. Approximatly 3 minutes. . .
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from Scituate, MA
Parts Used:
WB30M2
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Burned out surface element
This is an easy repair and for anyone thinking that they might have trouble effecting it, you all have my assurance that all the heat related elements are easily replaced. These elements are basically plug in and there is a shielded area (usually placed in the northeast quadrant of the burner unit. With everything turned off, pull the burnt out surface element up and toward the southwest. It should unplug from the female receptacle. Installing a new element involves performing this in reverse by coming into the surface with the prongs facing downward towards the receptacle and then pushing towards the northeast and downward at the same time The element should click into place. The entire time necessary to effect this repair should be less than ten minutes.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Thomas from Montgomery,, AL
Parts Used:
WB30M1
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
welded supports for the surface elements were broken
unplugged the broken elements and plugged in the new ones. Took about one minute. Tools used: hands and fingers.
Was this instruction helpful to you?
Thank you for voting!
Customer:
DeeAnn from Clinton, MO
Parts Used:
WB21X36771
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Knob had broken off
My husband was able to easily remove and replace the switch and know with-in 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Austin from Blackfoot, ID
Parts Used:
WB17X5113
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Poor connection to element
In a little over 15 minutes, I was able to pull the element and pan, snip the wires on the terminal block and use the wire nuts to fasten the new terminal block. The shrink wrap tubing went into place easily and all went back together easily. Best of all, the two year problem of a poor element connection was solved in a matter of minutes for a few dollars.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JAMES from STATE COLLEGE, PA
Parts Used:
WB17X5113
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Contact Burnout Inside Terminal Block
Pull out oven/range unit. Lift range top all the way up. Remove old terminal block. Make electrical connections using supplied wire nuts & heat shrink tubing. Heat shrink. Replace range top. Install coil burner & burner pan as unit. Done.
Was this instruction helpful to you?
Thank you for voting!
Customer:
ronald from YarmouthPort, MA
Parts Used:
WB17X5113
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Burned out terminal block
Hi, Very simple fix.Take out 1 screw & clip wire with snips. Put wires from new unit together & screw on wire nuts. Put shrink tubes on & heat with liter till it shrinks to what you want. A $15.00 fix is better than a $500.00 stove. FIRST STEP TURN OFF THE BREAKER & YOU ARE GOOD TO GO!!!!! Ron
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Anchorage, AK
Parts Used:
WB17X5113
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Socket set
Several burners quit working
Had one burner that was completely out as the old terminal block had a broken contact. The other burner was intermittent and would arc when heating up. There are several slightly different size terminal blocks. I had a hard time re-inserting one of the old burners into the new terminal block but got it to seat. I put a new burner with the new block on the other one and it fit much better. Additional tools used were a wire stripper and a heat gun for the heat shrink. The stove works great now.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rod from Huron, OH
Parts Used:
WB21X36771
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
rht. front element would not heat properly
I read parts select instructions and i was done in less than 30 minutes. Since 1988, this is the 1st. part that I had to replace. I now have parts select on my favorites list.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Thomas from Wildwood Crest, NJ
Parts Used:
WB30M2, WB17X5113
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
electric burner would not heat up
Pulled out the 8 inch surface element and then used a 1/4 inch socket to remove mounting screw for terminal block and pulled out block with attached wires as far as wires would permit. My range top does not lift up so I had to work thru surface opening but there was at least 10 inches of wire to pull out so it was not a problem. Cut existing wires at block, stripped 1/2 inch of insulation using my wire stripper pliers and wrapped wire ends of new terminal block and secured with wire nuts provided. Slipped on shrink insulation provided and applied flame from a hand held butane lighter. The instructional video on the web site was a great help. I may not have done repair without first watchng how easy it is. A cheap wire stripper is a great help. This supplier made it easy to select parts with fast delivery and complete the repair. Great source of appliance parts.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Leonard from Winter, WI
Parts Used:
WB21X36771
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
element heat wouldn vary
slid the range away from wall. disconnect power. removed back,compared switches and marked wires.installed new switch and wires.the adapter for the control knob was a problem it left the knob out futher than original i had to modify the plastic adapter and got it close enought! the most time spent was cleaning up the floor before putting the range back.
Was this instruction helpful to you?
Thank you for voting!
Customer:
FRED from Kenner, LA
Parts Used:
WB17X5113
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Replace terminal block
Simple repair. Easy to do. It was disappointing to receive replacement parts which were not ceramic terminals as depicted and described in words, but plastic and therefore will need to be replaced again soon. In addition the shrink tube was not large enough in diameter to cover the wire nut, both of which were provided with the replacement terminal. Part # PS232646 is not ceramic, but plastic which does not fair well in high heat applications.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dorothy from South Daytona, FL
Parts Used:
WB30M1
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
I needed to replace the 6" surface unit.
My GE range is 20 years old, and still going strong. All I needed was to replace the 6" surface unit. After making slight adjustments, it was just a matter of placing the new unit. After finding this Co. on the internet, and checking others, I will certainly order from Part Select again!Dorothy Trakshel
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joan from Wilmington, DE
Parts Used:
WB30M2
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
older element losing heat
really easy, remove old and replace with new...easy, once you have ordered and received the correct part.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sarah from San Andreas, CA
Parts Used:
WB31X5013
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Original trim ring did not fit
I had an appliance guy replace a burner(Calrod unit)on my 47 year-old GE range, but he didn't tell me that the original trim ring wouldn't fit. I decided to look up on PartSelect to see if I could get one to fit the new burner, and I did! Fits perfectly......no tools needed.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JBV42G*J1
91 - 105 of 122