Models > JBV42G*J1 > Instructions

JBV42G*J1 General Electric Microwave Oven Combo - Instructions

Jump to:

All Instructions for the JBV42G*J1
76 - 90 of 122
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Ann from San Antonio, TX
Parts Used:
WB30M2
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Surface element burned out
Removed old burner, plugged in new burner. Turned on electric and everything worked fine. I was concerned that I would not be able to get the correct burner since my stove is approximately 30 years old and General Electric no longer stocks replacement parts. The new surface element was manufactured by General Electric and had the correct replacement number on the package. Thanks Part Select.
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
KoLynn from Tempe, AZ
Parts Used:
WB31X5014, WB31X5013
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
I needed new trim rings around the stove burners
I logged into GE's website, put in my stovetop's requirements for size and type of trim rings, and was taken to partselect's site where I found what I needed. I ordered it and it came in less than a week!
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Barbara from Chesapeake, VA
Parts Used:
WB30M2
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
The burner stopped working
After checking at local appliance stores and unable to find the bunner I went online looking. I found this site and there it was. I ordered it, received it within two days, took the old one out and the new one in. As my granddaughter says, "easy peasy lemon squeeze". It took all of five seconds and I'm cooking again.
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
WILLARD from GLOVERSVILLE, NY
Parts Used:
WB21X36771
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
instructions could be better
it was hard to figure out the instructions from A switch to B switch to my switch. The first switch was no good the second one was good. prayer book didn't hurt.thank
0 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joseph from Baden, PA
Parts Used:
WB21X36771
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Front Burner,no control of.
The original controls were different for the small burners and the large burners. The replacement part fits all. Before removing wires, pay attention to writing on new and old control and replace 1 at a time. The hardest part was being sure to cut the knob stem to the correct length. Control works well.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Clifford from New smyrna beach, FL
Parts Used:
WB21X36771
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Burner constantly heated
Good directions
Was this instruction helpful to you?
Thank you for voting!
Customer:
Floyd from Warren, OR
Parts Used:
WB21X36771
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Plastic Insert for knob to long, had to use my bench grinder to cut it down
(Turn off the Power) Pull stove out, remove the 2 screws that holds switch in place, remove one wire at a time and install on new switch. Slip switch in replace 2 screws. Snap off about 3/4 of the shaft cut down plastic insert for knob, install knob turn on power and it works.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Nashville, AR
Parts Used:
WB21X36771
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
R had ight front control made loud noise when contacts opened.
This is twin oven range with controls at side of upper oven. Control panel was fastened with screws at top and bottom. Range has built-in hood at top which had to be disassembled to reach top screw. Once had access to top screw, eaisly removed control panel and replaced control. New control had identical connections as old control so only had to install it, break shaft to correct length, and use proper shaft adapter for knob. Remounted control panel and range worked perfectly. This would have been a very quick job except for having to deal with the built-in range hood.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Carol from Hamilton, OH
Parts Used:
WB21X36771
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Shaft for burner control knob broke off
I flipped breaker off for electic and confirmed that power to the stove was off. I removed the 2 screws holding the control unit in place. Carefully removed all knobs and buttons and pryed the cover for the control unit off. I then removed old part, removed the wired and clipped wires to the new unit. Put cover back on - has some difficulty getting the panel back in place to line up the screws. But after a couple of attempts, was able to line up unit and put screws in place to secure. Replaced all knobs. Turn breaker back on and cooked lunch. Very easy job. Most difficult part was getting panel back in position. I would watch alignment more carefully before I removed in next time. Easy home repair for Women...not sure about my man?
Was this instruction helpful to you?
Thank you for voting!
Customer:
stephen from Pittsburgh, PA
Parts Used:
WB19X10006
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set
Termonal burned off
I have had to replace this unit once before. It was very obvious which terminal had burned off. Removed the total front panel. Removed the timer and replaced wires from one unit to the other. Also had to strip off one wire connection and replaced it .
Was this instruction helpful to you?
Thank you for voting!
Customer:
Pierre from Pleasanton, CA
Parts Used:
WB19X10006
Difficulty Level:
Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable), Wrench set
Mechanical clock stopped advancing; replace with newer digital clock
1) Took photo of original wiring behind original clock. 2) Marked up wiring instructions for new clock with wire colors. 3) Marked wire colors next to posts on new clock. 4) Removed old clock and its metal mounting bracket. 5) Installed new clock onto old mounting bracket.PROBLEM: The holes in the glass facade of oven are shifted about 1/4" off from the pushbuttons on the new clock. 6) Remove bracket and enlarged holes by 1/4" sideways. This includes shifting the holes for the oven light pushbutton switches, and the four "racetrack" holes where the bracket attaches to the oven. Plug wires into new clock, using extender wires provided as needed. Labelled extender wires with their "colors". POWER UP. The clock works, and the "Timed Bake" works. However, the Self-Cleaning of the oven cannot be started, because the latch level cannot be moved to the right (locked ) position. This leaves us unsatisfied, as restoration of Self-Cleaning was the reason we decided to replace the oven clock.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dennis from Cerritos, CA
Parts Used:
WB30M2
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Stove Burners did not work.
The repair is simple, pull out the old, plug in the new. The most difficult aspect of the repair is to make sure that you have the right part. As this is an old stove, and it was a builder model, the model number did not match exactly, and I got the wrong part which I had to return. Look at the pictures carefully as many of the parts look similar.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mirtes from Marlborough, MA
Parts Used:
WB17X5113
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
heating element not heating
Removed the terminal block. Cut the wires. Cut the sheathing to expose the wire. Connected the new wires with the old wires by twisting them together. Added the wire nut and reconnected the block. Tested ok.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jilan from South Milwaukee, WI
Parts Used:
WB30M2
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Scorched Element
It wasn't so much the repair that was needed as how impressed I was with the fast delivery. Without a fourth burner & a holiday weekend coming up I was in desperate need of my element. I ordered it around 1:00 pm on a friday & it was delivered the next day before noon! Very impressed with the ease of ordering & receiving. Thanks again.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Howard from Fort Bragg, CA
Parts Used:
WB30M2
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
element burnt out
changed element
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JBV42G*J1
76 - 90 of 122