LE8457W2-PLE8457W2 Whirlpool Dryer - Instructions

take the old knob, insert the new one.

My 11 year old daughter broke the door clasp to the dryer by repeatedly slamming it trying to get it to close. I told her to go down stairs write down the make model and serial number and come back up and find a place to buy it online. I left with instructions not to use the computer for anything else until the part was found. Less then 15 minutes later I came back because I heard giggling. She was chatting but had found an exploded view of the door and the part. She was very pleased with herself! We bought it and it arrived a few days later. I saw the empty box. She had opened it and taken it down and installed it herself. A good lesson, for her and me

Well tried to find this simple part around Columbus and even maytag website no luck.Parts select had it to go and arrived earlier than expected.Fixed it less than 5 minutes works great.taken longer to put the light bulb back in,Really like the accuracy and quick response from parts select.If I had called a service tech probably would have cost $50.00 or more for a part that cost a little over $3.00 and saved this site in case I need to order other parts.Thank you

Followed the directions from a repair noted on the webiste. It was easy to follow. Thanks for the help!

Removed the front panel of the dryer and drum to replace the rollers. You will need a snap ring pliers to remove the locking snap ring holding the rollers, replaced rollers, installed new drum belt and replaced the front dyer panel.
Tested the dryer no more noise.

Thanks

I pried open the top of the dryer with a screwdriver. i took digital pictures (for reference)of 3 sets of wires needing to be unplugged during repair. I removed 6 nut screws to get to the repair. took the barrel out, replaced the pully wheel and belt paying attention to how they were originally. The pully was a little awkward to take off and put on, but not bad. My dryer purrs now. yahoooo!

After the dryer was opened up I took off the belt and removed the drum. To get the Idler Lever off I used a wrench to get the back of the bolt and loosened it with the socket. Then I placed the spring somewhere I wouldn't loose it while I bolted the new idler lever down. The spring stretched from the bottom to the new leveler with a little effort.

Pushed timer knob on - very simple. Pulled old door catch out and pushed new door catch in with needle nose pilers. Took about 5 minutes for both. Items were easy to locate on your website and shipping was fast. Thanks!!

The old door catch broke and fell into the unit. Ordered the new part which arrived fast and snapped it into place. Perfect fit and the door now closes/latches correctly - like new again. Would recommend your web site to all do-it-yourselfers. Loved browsing your site, especially seeing all of the schematics and parts list for my unit.

I ordered the part. ( I should have ordered just in case it happens again.) When it got here it took less than a minute to snap it in.

Loosened the screws, took out the old one. It shorted out to back. Inserted the new one attached wires, Installed screws and it worked

I used a screwdriver to pry out the broken door latch and inserted the new one in the same slot. Perfect fit. The picture of the part in the order page was a big help to identify the correct part.

Popped in the new part. Really! That easy!

as described in video. Very well done. Thank you

My problem was that my AMANA dryer would not heat. The site suggested testing the two thermostats so I opened the dryer but didn’t follow the instructions in the video tutorial on the site since my AMANA is different. I used a nut driver and needle-nosed pliers for the whole job. Here’s what I did:

1. Unplugged the dryer.

2. Disconnected the exhaust pipe at the dryer.

3. Pulled dryer away from back wall about two feet.

4. Removed the two bottom panel screws (floor level) and removed panel.

5. Removed the two door panel screws and removed door panel by pulling out at the bottom until the two spring clips released from the top panel.

6. Noted the colors of the wires going to the door switch and removed (green, black and white from left to right).

7. Noted the colors of the wires going to the lamp and removed (bottom - black and top - red.)

8. Removed the two top panel screws, lifted up the top panel and leaned it against a support.

9. Removed the four bulkhead screws and carefully lifted up and removed the bulkhead being sure to support the drum. Took note of the belt path around the motor and idler pulleys.

10. Reached under the drum and took the belt off the idler pulley and motor drive pulley.

11. Used the belt to lift and remove the drum through the front opening.

I noticed that the internal vent pipe had become disconnected (which probably caused internal overheating) so I fixed that.

I then removed the wires to the thermostats and tested both for continuity. The limit thermostat was bad. I also saw that the belt was becoming cracked. I ordered a new limit thermostat and belt.

Installation of the new parts was a snap. I removed the old thermostat with the nut driver and replaced with the new one and pushed the wire connectors back on. Replacing the belt was a little trickier but not a problem. (Be sure to route the new belt correctly as noted on Step 9 and place ribbed surface next to drum.)

I closed up the dryer by reversing the opening steps.