LE8457W2-PLE8457W2 Whirlpool Dryer - Instructions

The round exhaust duct in the back my dryer can be removed simply by pulling straight out. This gives full access to the belt tension wheel. Slip belt off the wheel, remove snap ring with snap ring pliers, remove washer and wheel. Install new wheel, attach belt, and reinstall duct by looking right down the middle to line up properly. Dryer sounds like new again. 10 minute job.

I began by removing the two screws at the lower part of the front panel. After removing the panel I was able to access and remove the broken switch which was located on the front panel. I popped out the old switch and replaced it with the new one, reattached the wires and put the front panel on and the jod was done.

I unscrewed the door catch and pried out with some resistance the strike part. Screwed in the catch and pushed in the strike. Closed door. Voila!! Back in business with assurance.

Removed front cabinet panel, removed lint/front drum panel, removed drum and belt. Removed spring from idler lever, replaced idler lever. Installed drum with drive belt, reinstalled front lint/drum cover, reinstalled front panel.

remove front part of the dryer and rise up the top to remove drum to replace the belt. than remove two screws for the heating element piece of cake repair.

My husband pulled drum out of dryer and replaced the idler pulley wheel and decided to replace the belt while he was in there. It's good to have a snap ring tool as it's a pain to replace the snap ring without this tool. Goes alot quicker!

Just follow the video. The hardest part is getting the top to disengage from the clips.

The dryer was squealing, so I looked videos on how to take the dryer apart. After I got it apart, I spun the roller wheels, the motor, and the idler pulley, and only the idler pulley gave an indication that it was sticking or not spinning appropriately, so I ordered the part and replaced it. And sure enough, it was the problem after all!

The front of the dryer needed to be taken off, the drum needed to be taken out and the belt installed on the wheel structure.
I was very pleased at how fast I received the part after ordering it! I will definitely use this site again when ordering replacement parts!

Unplugged the dryer. Took off the top back cover. Removed a plastic shield. I took a quick photo of the wires. Removed the knob--it fits very tight. Carefully pry off with a screwdriver. The metal clip stayed behind and I had to remove it from the shaft with a flat blade screwdriver. The timer is held on with two screws. Replaced the timer. Then did a one-to-one unplug-replug of the wires. The only glitch was the company changed the position of one of the terminals but it was still labeled the same. I replaced the knob with a good push. I put the plastic shield and back cover on. I plugged the dryer back in and it passed the test. Happy wife.

Disconnected dryer from vent and power receptacle, placed dryer on its back and remove the front panel by removing screws along the bottom of the panel and pulling down on the panel. Below the drum the element mounting plate was visible so I removed the sensor and element wires, removed the element mounting screws and pulled the element down and out of its "duct". I installed the new element and replaced the wires and front panel. That's all folks!

Went to YouTube and put in good.. did not fix the problem with the dryer but it has a new belt on it now!

disassembled the entire dryer drum and front bulkhead plate. Installed belt and replaced drum on rollers and positioned idler pulley .Video was very helpful in positioning drum and belt onto idler pulley. More trouble with the existing dryer vent replacement after repairs were complete

I pried open the top of the dryer with a screwdriver. i took digital pictures (for reference)of 3 sets of wires needing to be unplugged during repair. I removed 6 nut screws to get to the repair. took the barrel out, replaced the pully wheel and belt paying attention to how they were originally. The pully was a little awkward to take off and put on, but not bad. My dryer purrs now. yahoooo!

Followed the directions from a repair noted on the webiste. It was easy to follow. Thanks for the help!