AE9433 Whirlpool Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- jim from st. louis, MO
- Parts Used:
- WPY54414, WPW10121334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
excessive squeeling noise
replaced idler puller and washers
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Lakewood Village, TX
- Parts Used:
- WPY54414
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Broken Idler pulley
removed front, top cabinet, drum, belt and motor. replaced idler pulley on motor. replaced motor, belt, drum and cabinet parts. test ran fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Middletown, NY
- Parts Used:
- WP40111201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Dryer did not tumble.....Loose ....worn Belt
Fast delivery,,,, Easy installation
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Elk Grove, CA
- Parts Used:
- WP40111201
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Dry would not spin fast/ or would scream with heavy load
I took off the front panel removed the drum and took off the belt. I then installed new belt on drum then motor. Then installed the front panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Melbourne, FL
- Parts Used:
- WP40111201
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
needed new dryer belt
The repair went better than expected. I watched the video of how to replace the dryer belt and although it wasn't exactly the same, just by watching the video I was able to find my way through the process. Thank you very much for taking the time to create the video, it was very helpful and saved me a bundle of money by being able to do the repair myself.Thanks again!!! Dano, Melbourne Fl.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from La Crosse, WI
- Parts Used:
- WPY54414
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
replaced Idler pulley and bearing
Removed the front of the dryer. Took out the drum. Now everything inside is easy to get to. You do not need to remove the top. Upon inspection we found that we also needed to replace both felts, teflon guides, drive belt, and both support rollers ans shafts. Basically we rebuilt the dryer. It's quiet now and working like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steven from lincoln university, PA
- Parts Used:
- R9900489
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
would not start
replaced both fuses removed panel and removed fuses and checked for continuity and replaced with new fuses
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herminigildo from virginia beach, VA
- Parts Used:
- WP40111201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Belt cut in two
First I take off all front cover and then the dirt strainer next is the dryer drum holder next the top cover I lift up and so you room to set the dum belt
Was this instruction helpful to you?
Thank you for voting!
Blower wheel broken and rubbing on housing.
Removed front of dryer, first the lower then the upper front covers. Removed front drum support, front blower housing cover. Removed belt, and then motor with housing and blower wheel attached. Broke wheel and cover off motor, placed motor in vise to remove threaded nut from motor drive shaft (nut was seized). Reinstalled motor and belt. Installed new housing and blower wheel. Reassembled dryer. Note if old blower wheel had come off repair would have taken half the time and been significantly easier to perform.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerry from New Braunfels, TX
- Parts Used:
- 56000
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Wife let ink pin fall through lint trap and started dryer it broke fan.
Pulled off front of dryer because it made loud noise, lifted clothing drum removed cover for fan and order from model number on fan and replaced. 30 min with help from my son.
Was this instruction helpful to you?
Thank you for voting!