AE9433 Whirlpool Dryer - Instructions

Unplugged the dryer. Used the putty knife to release the spring clips. Opened the top and photographed then disconnected the wires at the top of the terminal block. Removed the old power cord and terminal block. Installed new terminal block. Reconnected wires according to pictures. Installed new power cord.

Replaced Thermostat Boosting heater and Cycling Thermostat located behind the front blower cowling. I did not remove the wiring until I had the new part so that i could connect them in the proper order.

i took the front off the dryer took belt loose took the tub out the plastic nut on the blower wheel striped out so i took the blower housing apart along with the motor got vise grips on blower wheel replaced motor blower wheel belt and belt tenchinor and spring cleaned all the lint put it back together works fine

I consulted the instructional video before starting to take the dryer apart. My model is older than the one used in the video but it was still very helpful. Putting the belt on was fairly easy; however, I didn't know I also needed a rear drum wheel as well so while the belt is installed, the dryer still doesn't tumble when anything is in it. Off balance without 2nd rear drum wheel.

removed front panels, open the top of dryer. Removed the three screws holding blower panels and removed them. Then removed belt, drum and replaced the pulley. In reverse order reinstalled the parts. Done all is quit and no more squeak.

I ordered the belt, which arrived really fast! Took dryer apart, removed old belt, replaced with new belt. The hardest part was remembering how to put the dryer back together! I think next time I will video the taking apart process so I can see how it goes back! This was the 2nd belt in about 18 years, the dryer works fine, and it sure is cheaper than a whole new dryer! Thanks for saving me money again! Really helps in these hard economic times!

Watched the video from part select and it was easy. I will always order from part select, I loved the delivery time!! I ordered two belts, one for my dryer and one for my sons. . . My belt arrived the next day and my sons only took two days. . . Now that is service. . Thank you part select

Once I realized the drum was to be removed, the actual repair was not difficult. Because of the location of the pulley, it's best to tilt the dryer. Snap ring pliers are required to remove the retaining ring on pulley. I pulled the damaged pulley from the bearing. A small gear puller was needed to removed the frozen bearing. Lightly oil the new bearing. Installing the drum is a challenge because of the loose belt. I used paint tape to hold the belt on the drum. Download the service manual for good exploded parts views.

I took the dryer apart and used the video on the website that helped a lot on how to install the belt and then we put it back together and dryer works great.

I openned the dryer and look for the problems. I found out the idle pulley was severly damaged. the driving belt was still ok however a piced of the belt backing was erroded. i found Part Select website and contact. The website is owsome! realy easy to follow and get youn to your needed parts. Customer service and the sales people are great. Also the video on the website is great and very easy to follow, they teach you how to install the parts. I had a very good experience with Part Select company. Thanks!

I was amazed just how easy it was. It would have been much quicker if I had a nut driver instead of a wrench. The video was great. Thank you!

for a while the dryer was really loud when on. i took the front cover, and could pin point it to the idler pulley wheel. i would squirt some wd 40 on the wheel just to get by. one day the dryer stopped turning so i thought the belt broke. after following the instructions on this site on now to take off the front panel, and tub holder (the panel that has the lint trap in it, i was able to take out the tub and find that the pulley wheel had broke apart. i ordered the new part and got a new belt at the same time. why not replace while i had it apart. i didnt have snap ring pliers to remove the snap ring so i got 2 small finishing nails that would fit in the holes and was able to pull apart the ring and get it off. i slid on the new wheel, and put the snap ring back on. ii watch the video on how to replace the belt and it was a sinch. the dryer was already apart and to fix it, took about 15 min. for $18 in parts, the dryer has never sounded better.parts select saves me money everytime.

I just followed the intructions from the video on the website. That made the replacement easy.

I did it just like the man in the video that was sent via e-mail by ParSelect,.

I was ordering a part for my daughter who needed a high limit switch and a fuse, it occurred to me after reading the troubleshooting helps on PartSelect that this was what I needed to change on my dryer also. With the help of your installation videos my daughter was able to repair her own dryer and save about $150.00 and I too was able to repair my own dryer and now it works great! Thanks