AE9433 Whirlpool Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Rochester, NY
- Parts Used:
- 61927
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Not much heat
Loosened the screws, took out the old one. It shorted out to back. Inserted the new one attached wires, Installed screws and it worked
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from NEPTUNE, NJ
- Parts Used:
- WP40111201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Drum would slip and at times not spin
You have to take apart the whole dryer to get to the belt.Nut driver with cordless drill make it go so much faster.Unplug dry, take apart dryer and replace with olr belt with new belt.Takes about 20 minutes to do.plus I took off the two guide wheels on back of cabinet and greased everything.Works like brand new.I had a repair guy tell me I needed a new motor.If you can spin the drum by hand replace belt first.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from fremont, NH
- Parts Used:
- WPW10116735
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
No heat
I dismantled the dryer and replaced the thermostat and the heating element. The online videos are excellent. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Rosholt, SD
- Parts Used:
- WPY54414
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
squeeking noise
used one nut driver, basically took the whole machine apart. took snap ring off the idler shaft, replaced pulley, and put it back together. simple job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DOUG from GRESHAM, OR
- Parts Used:
- 61927
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The dryer wasn't drying quick enough.
removed the lower cover, tipped the dryer on its back for easier access, unscrewed the 2 mounting screws removed the heating element, installed the thermostat and and high tempt relay on new one replaced the wires reinstalled the new element, very simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRED from ELK MOUND, WI
- Parts Used:
- WPW10116735
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Dryer would overheat at all temperature settings
replaced the limit thermostat,thermal fuse, and cycling thermostat. Bingo. Problem solved. Noticed that the back of cycling thermostat had a buildup of lint and I'm wondering if that acted as insulation and caused a wrong reading of temperature. Did not have to disassemble dryer as I could reach all parts with lower front panel removed. To make it easer to install new parts with one hand I lightly hot glued the screws through the new parts and taped the upper portion of new part to bulkhead. With everything lined up and no need to hold the screws I was able to attach using one hand. It was a reach but easily done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- april from lexinton, KY
- Parts Used:
- 61927
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
dryer not heating up
removed old element, relaced with new element , thermostat dryer works better than it has in along time
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maurice from East Falmouth, MA
- Parts Used:
- WPY54414, WP40111201
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
broken belt on drum
removed front of dryer, replaced old pully and put on new belt.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Wellsboro, PA
- Parts Used:
- WP40111201
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver
Replace drum belt
Leaned machine back and put blocking under machine to elevate. Removed two screws from front of bottom panel. Lift panel out and set aside. Next remove two bottom screws from door frame. Pull bottom of frame out and up to release. Remove wire clips from door light and switch. Set door frame aside. Inside drum, take three phillips head screws out, that hold filter frame in, remove filter frame. Next remove four front screws on drum alignment face plate. Set aside. Grasp drum and pull forward, off back guide rollers. Drum will drop down a little, reach in around drum and slide belt off. Remember to look in under drum to see proper placement of belt aroun motor shaft and idler pulley. Replace new belt around drum with ribs against drum. Route belt around motor shaft pulley, pull idler pulley toward motor and place belt around pulley smooth top runs against pulley. Reinstall everything you removed. Connect wires to door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from Lebanon, ME
- Parts Used:
- WPY54414, WP40111201, WP23748, WPW10121334
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
noisy
Took apart front of dryer, took out tub, replaced pully wheel, put tub back in with new belt, and put front back on. I would recomend replacing wear pads when doing this type of job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Pottstown, PA
- Parts Used:
- 56000
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set, Wrench (Adjustable)
The blower wheel was busted because somebody ran the dryer without the lint filter in. A cord and a fork were caught in it!
Fairly easy to repair once I figured out how to get it apart. The amazing part of this was searching the web for the part. I found PartSelect, ordered it at about 2pm Eastern time and the part arrived the next day! I will definitely use this service again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vickie from Lincoln, NE
- Parts Used:
- W10857122
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I needed a new grate where the water dispenses.
I just lifed the old grate off and layed the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from San Antonio, TX
- Parts Used:
- WP61923
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Black connection at terminal block burnt. Black wire was burnt through.
Unplugged the dryer. Used the putty knife to release the spring clips. Opened the top and photographed then disconnected the wires at the top of the terminal block. Removed the old power cord and terminal block. Installed new terminal block. Reconnected wires according to pictures. Installed new power cord.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Creswell, OR
- Parts Used:
- R9900489
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Dryer quit heating.
Replaced Thermostat Boosting heater and Cycling Thermostat located behind the front blower cowling. I did not remove the wiring until I had the new part so that i could connect them in the proper order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steven from islip, NY
- Parts Used:
- WPY54414, WP40111201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Horrible Sqweeling
When I first heard it sqweeling I tokk off bottom cover and peeked around the turned it on and it seemed to be coming from a back roller,I sprayed a little wd-40 and it went away,for a day ! Then I found parts select on line and found the problem. The belt had worn into the roller almost to the shaft. I ordered the roller and belt and watched the very helpful video and it took about 15 minutes!parts $29. 00 Piece and quiet without calling service guy priceless !! Thanks steven l. I. Ny
Was this instruction helpful to you?
Thank you for voting!