AE9233 Whirlpool Dryer - Instructions

My 11 year old daughter broke the door clasp to the dryer by repeatedly slamming it trying to get it to close. I told her to go down stairs write down the make model and serial number and come back up and find a place to buy it online. I left with instructions not to use the computer for anything else until the part was found. Less then 15 minutes later I came back because I heard giggling. She was chatting but had found an exploded view of the door and the part. She was very pleased with herself! We bought it and it arrived a few days later. I saw the empty box. She had opened it and taken it down and installed it herself. A good lesson, for her and me

one screwdriver, one new door latch, five minutes! Pried out the female part of the door latch, tapped in the new one and started the dryer. Never had an easier repair. Usually there is some hitch along the way you learn about the hard way, but not this time. TOO EASY!!

popped out the old, broken female latch, popped in the new one in less than 30 seconds. We had been leaning stool against the dryer door for 5 years. Now it works exactly like it is supposed to.

Removed old latch. Installed new latch. No problem.

The old door catch broke and fell into the unit. Ordered the new part which arrived fast and snapped it into place. Perfect fit and the door now closes/latches correctly - like new again. Would recommend your web site to all do-it-yourselfers. Loved browsing your site, especially seeing all of the schematics and parts list for my unit.

I used a screwdriver to pry out the broken door latch and inserted the new one in the same slot. Perfect fit. The picture of the part in the order page was a big help to identify the correct part.

After 20+ years of service, the plastic part that holds the dryer door closed, broke. I orderd the replacement part on a Monday and received it on Wednesday!
By applying constant pressure with my thumb, the replacement part 'snapped' into place - all of 4 seconds.
Fast delivery of parts and fast instal, made for a great day.

Repair part just snapped into place. It took longer to open the bag then do the repair. I thought it was going to be difficult to find a part for this dryer but partselect had the right part.
Thanks

Replaced the Latch

I followed the video on the site which was really helpful.I took the door off without problem. I had to take the bottom panel off the front and unscrew screws on large front panel.Replacing the latch was a breeze. Just as shown on video. Be careful that dryer drum doesn't fall down off wheels. My did and had to push it back up.Replaced all panels and screws and it works great.

removed the front of dryer panel below the door. Cleaned out all the lint. Pulled two screws with an extended nut driver. slid out the old element. I dentified the part . ordered, when the part came in I put a few simple componets on the new, slid it back in. Turned on the power to make sure it was working then reinstalled the front cover. works fine

The instructions that accompanied the part was extremely helpful. I removed two screws, lifted off the front panel, used the pliers to remove the old latch, pushed the new latch into the hole. I then replaced the panel (The part that is attached to the door was not broken). I tightened the two screws and the job was complete. I saved a very expensive service call. :)

Determined no air flow or heat through system even though dryer spun and timer worked. Ouside vent dispelled no air. Opened dryer panel.
Blower wheel/fan broken off from shaft. Googled appliance parts ... found ... Partselect .... keyed in mfg, model number ... schematics available ... found part ... ordered ... received in two days ... installed ... reassembled. Working fine ! $ 30.00 compared to buying new dryer ! This was a refreshing and rewarding repair. If it could always be this smooth !!! Great resource ... PARTSELECT !

Removed 2 screws on the bottom of front panel of dryer & pulled it off. Next I got down & looked to the back & bottom inside of the dryer. I spyed the heating element,I pulled off the two wires from the thermostats[ orange & black. I removed two screws from the heating element plate & dropped it down & removed it from the dryer. Reverse procedure to reinstall. Will see if we can get another 10 years service out of it.

Took 2 screws out of the bottom of the dryer so the front face plate came off. This allowed access to the door latch catch, which was easy to pull out with pliers. Pushed in new latch catch until it "popped" into place. Easy, easy, easy!