AE9233 Whirlpool Dryer - Instructions

Unplugged dryer removed the front, removed & marked the wires. Removed the drum & drive belt. Removed the snap ring on front of roller with a pgtai awl.Removed the wheel & worn washers, removed the nut on the back of the roller shaft. reppaced it all in reversed proceedure. Other than a few little scrapes on the knuckles it was Quite easy.

I guessed that a new belt may fix the problem. The repair was nearly as easy as the video suggested. I believe the dryer had been repaired before since there was a circular panel on the side which had been removed. I could reach in through the side to slip the new belt onto the pulley. The new belt now enables the drum to turn even for heavy loads.

After checking out a video showing how to change the belt I decided to tackle the job. First I pried up the top, there are two plastic tabs in the front corners that hold the top down to the front panel. The top swings upward and will stay in position while you continue to work. Using a 3/8 socket, I removed 4 bolts that hold the front panel onto the frame. Be sure to unhitched the wiring to the door switch and those to the control panel and then the front will come out by lifting it off the tabs in the lower corners. Put the front panel aside and slide the drum forward and out of the dryer frame. Remove the old belt noting how it ms oriented around the tensioner and motor pulley. Now everything should be exposed and you should take the time and clean the inside if I were you. Our dryer was filled with lint and dust but after a good vacuuming and wiping down with a damp sponge, it looked like new again. Put the new belt around the drum noting where it had sat before. There is a grove in the drum but our belt did not go inside their but on the drum itself. Slide the drum back in place and from underneath put the belt on the pulley and under the tensioner. Replace the front panel, rehitch the wires and put the top down and your done. My wife helped clean the inside which took longer than replacing the belt. Total time about an hour or so cleaning time included.

Disconnected dryer from vent and power receptacle, placed dryer on its back and remove the front panel by removing screws along the bottom of the panel and pulling down on the panel. Below the drum the element mounting plate was visible so I removed the sensor and element wires, removed the element mounting screws and pulled the element down and out of its "duct". I installed the new element and replaced the wires and front panel. That's all folks!

remove front of dryer with door to get to the back of lach pin. replace front. seprate innor and out door pieces use pliers to remove catch spring clamp ot replace catch screw innor and outor doors back togfther and put tools away your done

Disconnect power. First, remove the lower front panel, then the upper front panel (disconnect door switch wiring). Remove two screws holding the top panel to the left and right side panels. Remove wiring connections to light and humidity sensor. Remove four screws to front drum support assembly, lift up to disengage tangs, and remove assembly. Reach in and find the idler assembly for the drum drive belt, and unwrap the belt to loosen it, also removing the belt from the motor pulley.. Slide the drum out the front of the dryer along with the drive belt. Remove the snap ring (using snap ring pliers) and washer holding the idler pulley on to the idler assembly. Remove the idler pulley. Polish the shaft with fine steel wool to get rid of dirt. Clean thoroughly, leaving no steel wool residue. Install replacement pulley, washer, and snap ring. Reinstall drum, taking care to feed belt back into place as the drum is reinstalled. Reach in and wrap the belt around the motor pulley and the idler pulley. Reinstall the front drum support by lifting the drum slightly to allow the support to engage with the drum, and then drop it down to re-engage the tabs into the left and right side panels while reseating it into the blower intake. Install the four screws to hold it in place, and reinstall the wiring for the light and the humidity sensor. Attach the top panel to the left and right side panels with one screw for each side. Reinstall the upper front panel, including reattaching the wiring to the door switch, with two screws. Finally, reinstall the lower front panel. Reconnect to the power source, and you should be good to go.

The front of the dryer needed to be taken off, the drum needed to be taken out and the belt installed on the wheel structure.
I was very pleased at how fast I received the part after ordering it! I will definitely use this site again when ordering replacement parts!

Went to YouTube and put in good.. did not fix the problem with the dryer but it has a new belt on it now!

Just follow the video. The hardest part is getting the top to disengage from the clips.

The repair went very well. The parts were a perfect fit and arrived earlier than expected.It took a little longer than it should have to do the repair because of my recent surgery I had my 11 year old grandson operating the nut driver taking the dryer apart install the parts then reassemble under my watch full eye. You could say it went so easy a fifth grader could do it.

I tested all the thermostats and fuses and the heating element with a VOM. I found that the thermal fuse was bad and replaced that and it heats fine. The hard part was reaching everything from the front of the dryer. Poor design for access. Also replaced the door switch while I had it apart.

Removed the front panel of the dryer and drum to replace the rollers. You will need a snap ring pliers to remove the locking snap ring holding the rollers, replaced rollers, installed new drum belt and replaced the front dyer panel.
Tested the dryer no more noise.

Thanks

Followed video on PartsSelect website, they made it real easy.

removed a couple of screws and replaced the new fuse . the dryer is heating up ok now.

p.s thank you for the quick deliever on the part, . as i was only with out the dryer for two days

Thanks
JoAnn

My 11 year old daughter broke the door clasp to the dryer by repeatedly slamming it trying to get it to close. I told her to go down stairs write down the make model and serial number and come back up and find a place to buy it online. I left with instructions not to use the computer for anything else until the part was found. Less then 15 minutes later I came back because I heard giggling. She was chatting but had found an exploded view of the door and the part. She was very pleased with herself! We bought it and it arrived a few days later. I saw the empty box. She had opened it and taken it down and installed it herself. A good lesson, for her and me